Publicité
• Dust/chip extraction 6
- mount dust extraction device D as illustrated
- connect vacuum cleaner
! do not use dust extraction device/vacuum cleaner
when sanding metal
- clean dust extraction device D regularly for optimal
dust pick-up performance
• On/off
- switch on/off the tool by pushing switch E 2 in
"I"/"O" position
! before the accessory reaches the workpiece, the
tool should run at full speed
! before switching off the tool, you should lift it
from the workpiece
• Adjusting working speed 7
- with wheel F the required oscillating frequency can be
adjusted from low (1) to high (6) (also while tool is running)
- the optimal working speed depends on the material
and can be determined with practical trials
• Holding and guiding the tool
! while working, always hold the tool at the
grey-coloured grip area(s) 8
- keep ventilation slots G 2 uncovered
- do not apply too much presssure on the tool
(excessive pressure will cause excessive heat and
may shorten the service life of the accessory)
APPLICATION ADVICE
• Use plunge-cut saw blade H 2 for separating and deep
plunge-cuts in wood, plaster, gypsum and soft plastics
(also for sawing close to edges, in corners and other
hard-to-reach areas)
• For more tips see www.skileurope.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots G 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 9 will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60745, EN 61000,
EN 55014, in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
02.08.2010
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 92 dB(A) and the sound
power level 103 dB(A) (standard deviation: 3 dB), and
the vibration ✱ (hand-arm method)
✱ when sanding 8.8 m/s² (uncertainty K = 1.5 m/s²)
✱ when cutting with plunge-cut saw blade 13.9 m/s²
(uncertainty K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
significantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
F
Outil multifonctions
INTRODUCTION
• Cet outil est conçu pour le sciage et la découpe du
bois, du plastique, des métaux et des carreaux muraux
mous ainsi que pour le polissage de petites surfaces
• En raison de la commande oscillante, l'accessoire
pivote jusqu'à 21000 fois par minute pour 3°, ce qui
rend l'outil parfaitement approprié à un travail précis
pour des bords et des endroits étroits et d'accès
difficile
• Cet outil n'est conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
7
Jan Trommelen
Approval Manager
1150
Publicité
