Product Description - PLYMOVENT MOBILEPRO Manuel D'installation Et D'utilisation

Inlet pressure 5-10 bar (75-150 PSI)
Required pressure 5 bar (75 PSI) (by integrated pressure
regulator)
Compressed air G 3/8" (female)
connection
Compressed air 35 Nl (1.2 ft³) per pulse
consumption
Volume of compressed air 10 litres (2.6 gallon)
tank
Activation of filter - pressure controlled (threshold value:
cleaning system (online
only) - manually by push button
Duration of filter cleaning 60 seconds (6 pulses)
cycle
Fan
Fan type radial
Extraction capacity max. 1200 m�/h (700 CFM) (incl.
extraction arm)
Fan speed:
- 50 Hz - 2900 rpm
- 60 Hz - 3390 rpm
Noise level 72 dB(A) according to ISO 3746
Electrical data
Power consumption 1,1 kW (1.5 HP)
Available connection - 115V/1ph/50Hz
voltages - 115V/1ph/60Hz
- 230V/1ph/50Hz
- 400V/3ph/50Hz+N
Motor design IEC
Energy efficiency:
- single phase motor - n.a.
- three-phase motor - IE3 / premium
Mains cord:
- type - SJOOW 3xAWG14
- length - 4,5 m (14.8 ft)
Plug: Type:
- 115V/1ph/50Hz - none
- 115V/1ph/60Hz - NEMA 5-15P
- 230V/1ph/50Hz - none
- 400V/3ph/50Hz+N - none
Certification
IFA W3 pending
Refer to the available product data sheet for
detailed product specifications.
1.5 Dimensions
Refer to Fig. I on page 69.
1.6 Working range
Refer to Fig. II on page 69.
1.7 ambient conditions
Process temperature:
- min.
- nom.
- max.
Max. relative humidity
Suitable for outdoor use
1.8 Transport of the unit
You cannot hold the manufacturer liable for any transportation
damage after delivery of the product. Handle the machine and
the accompanying extraction arm with care. Completely
dismount the extraction arm before transport. Dismount the
arm by executing the mounting procedure in reverse order.
0000104750/210616/B MobilePro | MobilePro/PTFE
1000 Pa)
5°C (41°F)
20°C (68°F)
70°C (158°F)
90%
no
Subsequently the machine and the arm can be transported on
a pallet in the original packing.
To prevent damage, make sure that the machine and the arm
cannot shift on the pallet.
2

PRODUCT DESCRIPTION

2.1 Components
The unit consists of the following main components and
elements:
Fig. 2.1
A deflector plate
B filter cartridge
C dust tray
D handlebar
E control panel
F extraction fan
G outlet grid (2x)
H RamAir™ pulse amplifier (filter cleaning system)
A
B
C
Fig. 2.1 Main components and elements
2.2 Operation
The MobilePro works in accordance with the recirculation
principle. Welding fume is extracted through the hood of the
connected extraction arm by the built-in fan. The polluted air
passes the deflector plate
cartridge. The welding fume particles are collected at the
outside of the filter cartridge. The cleaned air is returned in the
workshop through the outlet grids on the sides of the unit.
2.2.1 Filter cleaning system
When the filter cartridge becomes saturated - and
consequently the extraction capacity reduces -, a pressure
switch activates the RamAir™ pulse amplifier, which thoroughly
cleans the filter cartridge by compressed air pulses. This
cleaning system can be activated manually as well. The dust
and dirt particles fall into the dust tray.
The cleaning system only operates when the fan is running, to
prevent dust particles to escape through the hood of the
extraction arm.
1. To protect the filter cartridge and to distribute the air equally inside the unit.
G H
and is cleaned by the filter
1
D
E
F
EN - 4