Replacement Parts - shark iQ Robot Self-Empty RV1000S Série Guide D'utilisation

REPLACEMENT PARTS

REPLACEMENT PARTS: ROBOT
Filter Robot Dust Bin
RVFFK950 129KY1000A
Self-Cleaning Battery
Brushroll RVBAT850
103KY1000
Brushroll BotBoundary
Door Strips
109KY1000 RVBBK850
Side Brushes
102KY1000
NOTE: To order replacement parts and filters, visit sharkaccessories.com.
sharkc le a n.com
REPLACEMENT PARTS: BASE
Base Dust Bin
104KY1000AE
Self-Empty Base
XSAESDOCK
Pre-Motor Foam &
Felt Filter Kit
106KY1000AE
Replacement
Post-Motor Filter
107KY1000AE
MAINTENANCE
CAUTION: Turn off power before performing any maintenance.
TROUBLESHOOTING
If any error lights are illuminated or flashing on your Shark iQ Robot™, see the error code
chart below:
ERROR CODE
CLEAN (RED) flashing
DOCK (RED) flashing
CLEAN (BLUE) + DOCK (RED) solid
CLEAN (RED) + DOCK (BLUE) flashing
CLEAN (RED) + DOCK (RED) flashing
DOCK (RED) + ! (RED) flashing
CLEAN (RED) + DOCK (RED) + ! (RED) flashing
CLEAN (RED) + DOCK (BLUE) alternating
CLEAN (BLUE) + ! (RED) flashing
CLEAN (RED) + DOCK (BLUE) + ! (RED) flashing
CLEAN (BLUE) + DOCK (RED) flashing
BATTERY ICON (RED) flashing
CLEAN (RED) + ! (RED) alternating
DOCK (RED) FLASHING + ! (RED) solid
DOCK (BLUE) + ! (RED) flashing
CLEAN (RED) + ! (RED) flashing
CLEAN (BLUE) + DOCK (RED) + ! (RED) flashing
For all other issues, please call Customer Service at 1-888-228-5531.
ERROR
SOLUTION
NUMBER
Robot may be stuck on an obstacle. Move robot to a new
10
location on a level surface.
Front bumper may be jammed. Clean the bumper and
6
make sure it moves in and out freely.
BotBoundary™ error. Move your robot to a flat surface
14
away from the magnetic boundary strip and try cleaning
again.
Cliff sensor error. Move your robot to a new location and
7
clean its cliff sensors.
Robot dust bin needs to be reinstalled. Insert the dust bin
9
until it clicks in place.
Side brush is stuck. Remove any debris from around the
2
side brushes so they move freely.
A drive wheel is stuck. Clean the wheels and remove any
2
debris wrapped around the axles so they can move freely.
Robot is stuck. Move your robot to a new location and
16
make sure the front bumper moves in and out freely.
Blockage in brushroll. Remove any debris from around the
2
brushroll so that it can spin freely.
Robot has encountered an error while booting. Please turn
21
the power off and back on.
Make sure your base indicator light turns blue to confirm
23
your robot is placed on the base correctly.
Battery is critically low and needs recharging. Please
pick up your robot and place it on the base. Make sure
24
the base indicator light turns blue to confirm your robot
is placed on the base correctly.
Blockage in brushroll. Remove any debris from around
2
the brushroll so that it can spin freely.
Blockage in dust bin. Check base and robot dust bin for
26
clogs. Clear any debris and reinstall the dust bin, ensuring
that it clicks into place.
Robot has encountered an error while charging. Please
24
make sure you are using the correct power cord for the
base.
Suction motor failure. Remove and empty the dust bin,
3
clean the filters, and remove blockages.
Wheel motor encoder failure. Please contact Shark
2
Customer Service at 1-888-228-5531.
s ha rkc l ea n.co m