Electrical Requirements; Water Supply Requirements; Connect The Water Supply - Whirlpool WRF954CIHB Guide De L'utilisateur

Electrical Requirements

WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it
is important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 volt, 60 Hz, AC-only 15 or 20 A fused, grounded electrical
supply is required. It is recommended that a separate circuit
serving only your refrigerator and approved accessories
be provided. Use an outlet that cannot be turned off by a switch.
Do not use an extension cord.
IMPORTANT: If this product is connected to a GFCI (Ground
Fault Circuit Interrupter) protected outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Food quality
and flavor may be affected. If nuisance tripping has occurred, and
if the condition of the food appears poor, dispose of the food.
NOTE: Before performing any type of installation or cleaning,
turn off cooling, and then disconnect the refrigerator from
the electrical source. When you have finished, reconnect the
refrigerator to the electrical source and turn on cooling. See the
"Using the Controls" section.

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi
(241 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call
a licensed, qualified plumber.
NOTE: If the water pressure is less than what is required, the flow
of water from the water dispenser could decrease or ice cubes
could be hollow or irregular shaped.
14
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out
of a reverse osmosis system and supplying the water inlet valve
of the refrigerator needs to be between 35 and 120 psi (241 and
827 kPa).
If a reverse osmosis water filtration system is connected to
your home cold water supply, the water pressure to the reverse
osmosis system needs to be a minimum of 40 to 60 psi (276 to
414 kPa).
Check to see whether the sediment filter in the reverse
■
osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill
■
after heavy use. The tank capacity could be too small to keep
up with the requirements of the refrigerator.
NOTE: Faucet-mounted reverse osmosis systems are
not recommended.
If your refrigerator has a water filter, it may further reduce
■
the water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See the "Water
Filtration System" section.
If you have questions about your water pressure, call a licensed,
qualified plumber.

Connect the Water Supply

Read all directions before you begin.
IMPORTANT:
Plumbing must be installed in accordance with the
■
International Plumbing Code and any local codes and
ordinances.
Copper and PEX tubing connections from the household
■
water line to the refrigerator are acceptable and will help
avoid off-taste or odor in your ice or water. Check for leaks.
If PEX tubing is used instead of copper, we recommend the
following part numbers: W10505928RP (7 ft [2.14 m] jacketed
PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP
(25 ft [7.62 m] PEX).
Install tubing only in areas where temperatures will remain
■
above freezing.
Tools Needed:
Gather the required tools and parts before starting installation.
Flat-blade screwdriver
■
7/16" and 1/2" open-end wrenches or 2 adjustable wrenches
■
1/4" nut driver
■
NOTE: Do not use a piercing-type or 3/16" (4.76 mm) saddle
valve, which reduces water flow and clogs easier.