ATIKA BWS 700 N Notice Originale page 12

Operating times
Before initiating the device please observe the provisions pertaining to
corresponding laws (regional provisions) for the noise control.
Symbols machine
Carefully read opera-
tor's manual and the
safety instructions be-
fore starting the
machine and observe
the instructions when
operating.
Wear safety shoes.
Wear ear protection.
Use light-duty breathing
protection.
Shut off engine and remove power cord before
performing cleaning, maintenance or repair work.
Warning of hot surfaces. Danger of burning! Do not touch
hot engine parts.
Direction of saw blade rotation
This product complies with European regulations
specifically applicable to it.
Electrical devices do not go into the domestic rubbish. Give
devices, accessories and packaging to an eco-friendly
recycling.
According to the European Directive 2012/19/EU on electrical and
electronic scrap, electrical devices that are no longer serviceable must
be separately collected and brought to a facility for an environmentally
compatible recycling.
Symbols operating instructions
Threatened hazard or hazardous situation. Not observing
this instruction can lead to injuries or cause damage to
property.
Important information on proper handling. Not observing
this instruction can lead to faults.
User information. This information helps you to use all the
functions optimally.
Assembly, operation and servicing. Here you are explained
exactly what to do.
Please refer to the attached assembly and
,
operating instruction sheet for references to
,
figure numbers in the text.
,
...
12
Normal intended use
Wear protective
gloves.
Wear eye
protection.
Wear protective
clothing.
Risk of injuries of
fingers and hands
by the saw blade.
Risidual risks
Even if used properly, residual risks can exist even if the relevant safety
regulations are complied with due to the design determined by the
intended purpose.
Residual risks can be minimised if the "Safety instructions" and the
"Normal intended use" as well as the whole of the operating instructions
are observed.
Observing these instructions, and taking proper care, will reduce the risk
of personal injury or damage to the equipment.
In addition, in spite of all the precautionary measures taken, non-obvious
residual risks can still exist.
This machine is designed for cross cutting firewood in the house and
hobby field.
Cutting of round material having a diameter smaller than 30 mm and
greater than 240 mm is not allowed as these pieces can not be held
safely.
The length of the material to be cut must not exceed 1000 mm. The
length of the material must be 200 mm as a minimum.
Only high-quality saw blades acc. to EN 847-1 up to a max. diameter
of 700 mm must be used.
Because it has no extraction device this machine must only be used
outdoors.
Only work pieces are allowed to be processed which can be safely
placed and held in the jigging device.
The use of saw blades made of HSS steel (high-alloy high speed
steel) is not permitted since this steel is hard and brittle. Risk of injury
through saw blade breakage and expulsion of saw blade pieces.
The intended usage also includes compliance with the operating,
servicing and repair conditions prescribed by the manufacturer and
following the safety instructions included in the instructions.
The relevant accident prevention regulations for the operation as well
as the other generally acknowledged occupational medicine and
safety rules must be complied with.
Any other use is deemed not to be intended use. The manufacturer is
not liable for any type of damage resulting from this: the user bears
the sole risk.
Unauthorized modifications to the saw preclude any liability of the
manufacturer for resulting damages of any kind.
The saw may only be equipped, used and serviced by persons who
are familiar with it and have been instructed on the hazards. Repair
works may only be carried out by us or by a customer service agent
nominated by us.
The machine may not be used in a potentially explosive environment
or be exposed to rain.
Metallic parts (wires etc.) have unconditionally to be removed from
the material to be cut.
Danger of injury of fingers and hands by the tool (saw blade) or work
piece, e.g. when replacing the saw blade.
Injury by catapulted workpiece parts.
Throwback of the workpiece or workpiece parts.
Breaking or catapulting of saw blade.
Risk from electricity, by using non-standard electrical connections.
Touching live parts of opened electrical components.
Impairment of hearing when working on the machine for longer
periods of time without ear protection.
Emission of harmful wood dusts. Wear therefore a protective mask.
Noise emission: Use saw blades designed for noise reduction and
keep the machine in a good condition.