Publicité
Les langues disponibles
Les langues disponibles
• SET UP
Each Camera Unit is mains (AC) powered. Ensure each unit is connected to a suitably located domestic mains supply
using the adaptor supplied.
It is possible to pair up to four camera units to any one parent unit, however connecting each additional camera
unit must be conducted individually (one after another) and not simultaneously.
Although it is possible to connect multiple camera units to any parent unit, it is only possible to watch one camera
at any time. Full instructions for switching between Camera units are given below.
• CONNECTING ADDITIONAL CAMERA UNITS TO YOUR EXISTING MONITOR
a.
With the existing monitor (camera and parent unit) correctly set-up and operating as normal, activate
the new Camera unit by pressing and holding the ON/OFF
b.
Once active, press and hold the new Camera Units ON/OFF
until both buttons start to flash.
• WITHIN 60 SECONDS OF THE ABOVE;
c.
Enter the Parent Units 'Multi Camera Monitoring' sub menu.
d.
Scroll along to the
'Add a
Camera' ("+") screen and press the 'select' button, at which point the Parent
Unit shall enter 'connect mode' indicated by the 'connection sequence' (shown below).
Add a Camera
Connection Sequence
e.
Once successfully connected the 'connection sequence' shall automatically be replaced by the Video Feed
from the newly connected monitor.
f.
If a connection is unsuccessful repeat the above, ensuring steps b – d are conducted with 60 seconds of
each other. Also try switching the existing Camera unit(s) OFF until a connection is made.
• SWITCHING BETWEEN CAMERA UNITS
With more than one camera connected (and activated), it is necessary to switch feeds between camera units using
the following steps:
a.
Enter the Parent Units 'Multi Camera Monitoring' sub menu.
b.
The currently selected camera (number) will be displayed.
c.
Scroll across the additional cameras, pressing the select button to view your desired video feed.
Interference may occur if the Camera units are located within close proximity to each other.
GB
Button for more than 2 seconds.
Button and Nightlight
buttons together
IMPORTANT! It is only possible to visually and audibly monitor one camera at any time. Meaning that events occurring
in vision of other camera units will go unnoticed until the manual process to view each camera is undertaken.
If connecting a Tomy Movement Sensor Pad TSP500 with a Camera Unit, the movement clicks and alarms shall only
be heard through the Parent Unit if the connected camera is being viewed. At all other times the Movement Pad
Monitor functions shall revert back to that units control module.
• CARING FOR YOUR MONITOR
Do not immerse any parts in liquids. Do not place in direct sunlight. Periodically examine product for signs of damage
to electrical parts and do not use until damage has been properly repaired. Always remove batteries from the Baby
Unit if using the mains adaptor for long periods of time.
• GUARANTEE
We guarantee your monitor against manufacturing defects for 2 years from the date of purchase on production of
a valid receipt. In the first instance of a manufacturing defect, we recommend that you return your monitor to its
place of purchase. If this does not satisfactorily resolve your problem, please refer to www.tomy.eu for further advice.
Full terms and conditions can be found on our website: www.tomy.eu
• TECHNICAL SPECIFICATIONS
- Power Supply: Mains adaptor rating: PRI: 100-240V~50/60Hz SEC: 6V
- Batteries: Parent Unit - Rechargeable 1500mAh 3.6V Ni-MH battery (included).
- Operating Range: 250m in optimum 'open field' conditions.
- Operating Temperature: 0 - 50ºc.
- Frequencies: 2400~2483.5MHz.
• SAFETY INFORMATION
IMPORTANT! This monitor is restricted for indoor use only! The Tomy Baby Monitor is designed to help you monitor your child
and is not a substitute for adult supervision. This product is not a toy. Always keep electrically operated items and their cables
out of reach of babies and younger children. Under no circumstances should you place any part of your monitor in or on a
cot. Ensure all wiring is positioned safely so that children cannot become entangled and that no trip hazard is created. Under
no circumstances should the adaptors supplied with this monitor be used with any other equipment. No other adaptors than
those supplied should be used with your monitor. Be careful not to position the adaptor where a child is likely to use it as a
step. Putting weight on the adaptor while it is plugged in could damage the unit or cause injury to your child. It is normal for
chargers to become hot during use – take care when handling, allow heat to disperse. DO NOT COVER. Disconnect charger if the
product will not be used for several days. To prevent a shock hazard, please disconnect from power supply before cleaning.
Help the environment by disposing of your product and packaging responsibly. The wheelie bin symbols
indicate the product and batteries must not be disposed of in the domestic waste as they contain substances
which can be damaging to the environment and health. Please use designated collection points or recycling
facilities when disposing of the item or batteries.
GB
550mA.
Publicité
