Technical Data - METAWOOD MTMS1200-210-21 Traduction Des Instructions D'origine

_ Remove the shaft bolt and the outer saw flange
from the saw shaft.
_ Remove the saw blade from the saw shaft and lift
it up to remove it from the machine.
_ Remove the shaft nut and the inner saw flange
from the saw shaft.
_ Clean the surfaces of the following components:
-The saw shaft
-The inner saw flange
-The saw blade
-The outer saw flange
-The shaft nut
-The saw blade guard
HAZARD! Do not use any
cleaning products (for instance
for removing resin
residues) that have the tendency
to cause corrosion on light
metals; this could damage the
HAZARD! Be sure to fasten the
inner saw flange correctly! The
saw may block, or the saw blade
may come lose, if the flange is
not correctly fastened. The inner
saw flange is correctly mounted
when the bevelled collar points to
the right and the spring groove
_ Mount the new saw blade and check the rotating
direction (the arrow on the saw blade
must point in the same direction as the arrow on the
saw blade guard!).
HAZARD! Only use saw blades
that conform to the applicable
standards and that can be used at
the maximum speed indicated in
the technical data sheet.
_ DO NOT use:
- Wrong saw blades
- Saw blades made of high-speed steel (HSS)
- Damaged saw blades
- Saw blades with missing teeth
HAZARD!
_ Only use OEM components for installing the saw
blade.
- Do not use loose reduction rings; the saw blade
could come loose.
- Saw blades must be mounted in such a way that
they cannot wobble, and that they cannot
come loose during operations.
_ Install the outer saw flange.
_ The two flanges must fit over the surfaces of the
saw shaft.
_ Insert the shaft bolt (left-turning thread) and
tighten with a hexagonal spanner.
HAZARD!
_ Do not lengthen the spanner, so that you can
exercise more power.
machine.
points to the left.
_ Do not hit on the spanner with a hammer, for
tightening the shaft.
_ The spanner must be removed, after the shaft that
has been tightened.
_ Install the saw table and mount the corresponding
screws.
Cleaning
Use a brush, a dust cloth or vacuum cleaner, to
remove all wood chips and sawdust from:
* The adjustment facilities
* The operating components
* The motor ventilation openings
* The space under the table gap.
Storage
_ Thoroughly clean the whole machine and its
accessories.
_ Store it out of the reach of children, in a stable and
secure position, in a cool and dry place,
avoid too high and too low temperatures.
_ Protect it from exposure to direct sunlight. Keep it
in the dark, if possible.
_ Don't keep it in plastic bags to avoid humidity
build-up.
Replacing coal brushes
Remove and check the carbon brushes regularly.
Replace when they have worn down to the limit
mark. Keep the carbon brushes clean and free to
slip in the holders.
Both carbon brushes must be
replaced at the same time.
Only use original carbon

TECHNICAL DATA

Mains voltage V
Mains frequency Hz
Power input W
Speed min-1
Speed max. for blade min-1
Saw blade diameter mm
Blade bore mm
Min./Max tooth thickness mm
Max. depth of cut
table saw position mm
cut-off saw position mm
Max. cutting capacity (thickness x width) in the cut-
off saw position
0° mitre, 0° bevel mm
45° mitre, 0° bevel mm
0° mitre, 45° bevel mm
45° mitre, 45° bevel mm
Bevel angle
Table dimensions Max. mm
Table dimensions Min. mm
HAZARD!
brushes.
230
50
1,200
4,300
6.000
210
30
2.0/2.6
33
55
55 x 115
55 x 65
35 x 115
20 x 40
0-45°
380 x 270
362 x 250
(without slot)
41