Publicité
Les langues disponibles
Les langues disponibles
more safety warnings
„Power tool use and care"
Switch off machine and pull out power plug out of the power
outlet in case of:
−
Contact of chain saw with soil, stones, nails or other
foreign substances
Check immediately chain and guide bar.
Carrying out repair work.
−
Performing maintenance and cleaning work.
−
Eliminating faults.
−
Transport.
−
Clamping again the chain.
−
Chain change.
−
Leaving of machine (also for short-term interruption).
−
Check the machine for possible damage:
Before further use of the machine the safety devices
−
must be checked carefully for their proper and intended
function. Only operate the machine with complete and
correctly attached safety equipment and do not alter
anything on the machine that could impair the safety.
−
Check whether movable parts function perfectly and do
not stick or whether parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the machine.
−
Damaged safety devices and parts must be properly
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
−
Damaged or illegible safety labels have to be replaced.
Store unused devices in a dry, locked place.
more safety warnings
„Service"
Do not carry out repair operations on the machine other
than those described in section "Maintenance" but contact
the manufacturer or authorized customer service centres.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer is
not liable for any damage or injury resulting from such
action.
more safety warnings
„Chain saw safety warnings"
• Primary users
Persons working for the first time with the chain saw must
obtain a practical instruction on the use of the chain saw and
the operator protection equipment by an experienced
operating person. Primary users shall first of all practice
cutting of round timber on a sawhorse or a rack.
• Minors are not allowed to work with the chain saw.
• This device is not intended to be used by persons (including
children) with restricted physical, sensory or mental abilities
or a lack of experience and/or know-how unless they are
supervised by a person responsible for their safety or they
have been instructed by such a person on the use of the
device.
• Children must be supervised to make sure that they do not
play with the device.
more safety warnings
„Causes and operator prevention of kickback"
Kickback
Carry out lateral cuts, diagonal cuts and longitudinal cuts
with increased attention because here the claw stopper is not
put on.
How to avoid saw backstroke?
Always hold the chain saw firmly with both hands.
For better control saw with the lower edge of the guide
bar. Hold the chain saw as close as possible to the
horizontal position when contacting wood.
Never saw with the guide bar tip.
Sawing with the upper guide bar edge may cause a
saw backstroke if the saw gets jammed or hits a hard object
in the wood.
Start cutting only with running saw chain.
Only work with correctly sharpened and clamped saw chain.
Use claw stopper (16) as lever.
Never work above height of shoulders.
Never cut through several perches at the same time. When
releasing make sure that no other perch is touched.
If possible use a sawhorse when cutting to length.
Stab cuts shall only be carried out by instructed personal.
Vibrations
Hand arm vibration a
= 4,824 m/s²
h
Measuring uncertainty K
= 1,5 m/s²
hd
The indicated vibration emission level has been measured
according to a standardised test method and can be used to
compare power tools.
It can also be used for an initial estimate of the vibration exposure.
The actual vibration emission level during the use of the
machine may differ from that indicated in the operating instructions
or indicated by the manufacturer.
This may be caused by the following factors to be minded before
and during the use:
− Proper use of the machine
− Correct cutting or machining of material
− Proper condition of the machine for use
− Use of the correct and sharp cutting tool
− Handles and optional anti-vibration handles properly
mounted on the machine body
When you feel uncomfortable or notice discoloration of skin on
your hands during the use of the machine, stop working
immediately. Observe sufficient break times to rest. Failure to
have sufficient break times may result in a hand-arm vibration
syndrome.
The extent of exposure depending on the type of work or machine
use should be estimated and appropriate breaks taken. In this
way, the extent of exposure can be considerably reduced over the
entire work time. Minimise the risk caused by vibrations. Maintain
this machine according to the instructions in the manual. If you
intend to use this machine frequently, contact your local
authorised dealer and purchase anti-vibration accessories if
required. Avoid the use of this machine at temperatures under
10°C. Create a work schedule in order to minimise vibration
exposure.
23
Publicité
