Hoshizaki IM-240AME Notice D'installation page 2

IMPORTANT
1. In order to carry out safe and proper installation of the product,
please read this booklet carefully beforehand and follow the
instructions contained within.
2. On completion of the installation, start up the icemaker to
check for any abnormalities, and instruct the user on how to
use and maintain the icemaker in accordance with the
Instruction Manual.
3. This booklet should be handed over to the user after the
installation and be preserved by the user together with the
Instruction Manual for any further consultation that may be
necessary.
The installation must be carried out by qualified
personnel, in accordance with current regulations, according
to the manufacturer's instructions.
1. UNPACKING
Children should not be allowed in reach of the packaging elements
(plastic bags and expanded polystyrene) as they are potential
sources of danger.
Remove shipping carton, tape(s) and packing. If packing material
is left in the icemaker, it will not work properly.
Power Cord
Top Panel
Front Panel
Note: This icemaker needs a Storage Bin. The recommended Storage
Bin is HOSHIZAKI ICE STORAGE BIN, Model B-300SD(PD) or B-
500SD(PD) with Top Kit - 8C, B-700SD(PD) with Top Kit - 22C, or
B-900SD(PD) with Top Kit - 22C and Top Kit - 8C.
1) After removing the packaging, make sure that the icemaker and the
Storage Bin are in good condition. If in doubt, please do not use the
equipment but apply to professionally qualified personnel. See the
instruction sheet attached to the Storage Bin for its unpacking and
installation guidelines.
2) Remove the icemaker panels to gain access to the accessory kit
and to assist easier installation.
Front Panel
Top Panel: Remove the screw. Lift off.
Front Panel: Remove the screw. Lift up and pull
toward you.
Side Panel: Remove the screw. Pull slightly
toward you, and lift off.
WARNING
WARNING
CAUTION
Fig. 1
Top Panel
Side Panel
Fig. 2
3) Remove the package of accessories, and check the contents:
a) Installation Kit (Air-Cooled)
Inlet Hose
Outlet Hose
Installation Kit (Water-Cooled)
Inlet Hose
Outlet Hose
1/2-3/4 Nipple
b) Scoop
c) Ice Chute
d) Drain Pipe Collar
e) Packing
f) Mounting Bracket
4) Remove the shipping tape holding the Bin Control Switch.
5) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
2. LOCATION
1. This icemaker is not intended for outdoor use. Normal operating
ambient temperature should be within 1°C to 40°C. Normal
operating water temperature should be within 5°C to 35°C.
Operation of the icemaker, for extended periods, outside of
these normal temperature ranges may affect production
capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for the
equipment.
4. Allow 60 cm clearance at rear and top for proper air circulation
and ease of maintenance and/or service should they be
required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top of the icemaker or in front of the
Louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero.
3. INSTALLATION
* Incorrect installation can cause harm
to people, animals or things, for which
the manufacturer cannot be held
responsible.
1) Fully screw in the four legs provided
(bin accessory) into the Storage Bin
underside. See Fig. 3.
2) Position the Storage Bin in the selected
permanent site.
3) Place the icemaker on top of the
Storage Bin by holding the bottom.
4) Secure the icemaker to the Storage
Bin, by using the two mounting
brackets and two bolts provided. See
Fig. 4.
1
ENGLISH
1
1
2
2
2
1
1
1
1
2
IMPORTANT
Bottom Plate
Adjustable Legs
Fig. 3
Bolt
Mounting
Bracket
Fig. 4
Icemaker
Bin