Original Instructions - Dremel Work Station 220 Traduction De La Notice Originale

GB

ORIGINAL INSTRUCTIONS

USED SYMBOLS
READ THESE INSTRUCTIONS
USE A DUST MASK, HEARING AND EYE
PROTECTION
POWER TOOL SAFETY RULES
WARNING
!
INSTRUCTIONS PROVIDED WITH THE
WORKING STAND AND THE POWER TOOL TO BE
MOUNTED. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
SAVE all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
SAFETY RULES FOR WORKSTATION
a. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments or changing accessories
Accidental starting of power tool is a cause of some
accidents.
b. Properly assemble the working stand before
mounting the tool. Proper assembly is important to
prevent risk of collapse.
c. Securely fasten the power tool to the working
stand before use. Power tool shifting on the working
stand can cause loss of control.
d. Place the working stand on a solid, flat and level
surface. When the working stand can shift or rock, the
power tool cannot be steadily and safely controlled.
e. Know how to shut off the tool! Position the tool so
that switch is readily accessible to quickly shut off in
an emergency.
f. Route the cord away from the bit or cutting area.
Cutting into live electrical wires may result in a shock,
burn or electrocution.
g.
Wear eye, ear protection and dust mask. Using
personal safety devices and working in safe
environment reduces risk of injury.
h. Do not wear gloves or loose clothing during
operation of the tool.
i. Match the appropriate bit and its speed to your
application. Do not use bits that have a cutting
diameter that exceed the capacity of the tool. The
drill press stand is intended primarily for light duty use
on wood, plastic and metal. Overloading the tool can
lead to personal injury or tool failure.
READ ALL SAFETY
WARNINGS AND ALL
j. Never use dull or damaged bits. Sharp bits must be
handled with care.
k. Always make sure the workpiece is free from nails
and other foreign objects.
l. Before operation clamp workpiece or brace against
column. Never hold a workpiece in one or two
hands while drilling. Clamping the workpiece allows
you to use both hands to control the tool (PICTURE 7).
m. Use a "V" block for supporting round stock such
as tubes or rods when drilling. Round material such
as dowel rods, pipes or tubing have a tendency to roll
while being cut, and may cause the bit to "bite" or the
workpiece to jump toward you.
n. You must set and lock tool head into the desired
position and depth of cut when performing
operations other than drilling. Bring the workpiece
to the tool and allow for sufficient space between
your hand and the spinning bit.
This Drill Press was designed for drilling, sanding,
brushing, polishing or grinding applications, other
applications may present hazards that cannot be
adequately guarded.
If the side of any rotating accessory is used to perform
the work, for example a sanding drum, the workpiece
must be positioned on the side of the accessory that
rotates against the feed direction of the workpiece.
Placing the workpiece on the side of the accessory
where the feed direction and accessory rotation are
the same may cause the workpiece to be pulled by the
rotating accessory and lead to loss of control during
operation.
o. Never start the tool when the bit is engaged in the
material.
p. Wear a dust protection mask when working with
materials which produce dust that is detrimental
to health; inform yourself beforehand about the
materials to be worked on.
q. After changing the bits or making any adjustments,
make sure the collet nut and any other adjustment
devices are securely tightened.
r. Never touch the bit during or immediately after
the use. Contact with a spinning bit will cause injury
and after use the bit is too hot to be touched by bare
hands.
s. Do not leave a running tooling unattended, turn
power off. Only when tool comes to a complete stop it
is safe to remove workpiece and clean the stand.
ASSEMBLY (PICTURE 1)
ATTACHMENT FOR USE WITH DREMEL ROTARY
MODELS 200, 3000 AND 4000
PICTURE 1
A. Hanger assembly
B. Cap
C. Hanger wire
D. Cord holder
E. Wrench
F. Crows nest
G. Height adjustment lever
H. Square nut
I. Drill press
J. Tool holder
K. Tube assembly
L. Base hex bolt
M. Base
8