Assembly / Installation; Activating The Remote Control - Jensen Dynamique Mode D'emploi

Assembly / installation
First of all you should check whether all the
parts have been supplied by referring to the
summary on the left-hand side of the folder.
1. Turn the base upside down. Screw the feet
or wheels onto the legs and attach these to the
base. Use 1 screw for each leg.
2. Attach all the plastic corner attachments to
the base.
3. Lay out the support sections of the bed in
the correct order.
4. Position the base in such a way on the
sections that the section attachment points are
exactly above the corner attachments. Make
sure that no cables get caught.
5. Secure the base to the support sections,
inserting the 16 screws through the corner at-
tachment points. Fasten the 4 screws on each
section by hand before tightening.
Pull the leads from the massage motors
through the cable ducts to the control unit at
the foot end.
Make sure the leads with the coloured strips
(the massage motor and air-conditioning leads)
are linked to the control unit cables which have
the same coloured-coded strips.
6. The storage pouch can be attached to either
one of the sides of section 1 using 2 screws.
You can decide which side yourself.
7. Place the mattress and the mattress topper
on the support sections. Now you can plug the
bed into the mains.
8. Connect the network adapter to the leads
poking out of the cable guide in the frame at the
head end. Then insert the plug into the socket.
9. When you use this function for the first time,
raise the head end gradually, after activating the
bed's remote control, and check whether the
massage or the lighting leads are not pulled too
tight. Keep moving the bed until it has gone as
far as it can.
6
Introduction
Congratulations on the purchase of your Jensen Dynamique adjustable
bed. We hope that it gives you many years of comfortable days and
nights. During the development of the Jensen Dynamique, special atten-
tion was paid to ensuring that it is simple and safe to use. The advanced
technical features can be operated simply and smartly using the handy
remote control. We recommend that you read the instructions below to
familiarise yourself with its use.
Guarantee
We provide a 5 year guarantee based on normal use. The invoice on
which the date of purchase is stated serves as a certificate of gua-
rantee. In the event of any faults or malfunctions, please contact
the store from which you purchased the bed.
Using the remote control
Insert the batteries (2 x AAA) into the remote control. The remote control must be activated
(See 'Activate the remote control') before you can operate the bed.
• The remote control can control the movement of the bed via the joystick if you keep it
vertical, with the display facing downwards.
• If the display is pointing upwards, you will be able to use the menus with the joystick.
Move the joystick to the side to view the clock.
Push the joystick to view the menu. Use the joystick to move the marker to the desired fun-
ction and then press it. Set the function at the desired level. If unused, the display will switch
to energy saving mode within 15 seconds.
Activating the remote control
Activate the remote control for the right bed by pressing the button on the control unit under
the bed (see illus. 6). Keep this button pressed until it emits a double audible signal and then
release. Keep the remote control vertical, with the display facing down and move the joystick
to the left or the right to synchronise the remote control with the control unit.
The remote control has now been activated in conjunction with the control unit and the
electric motor under the bed.
NOTE: When you move the remote control to the left or the right in order to connect it to the
control unit, it is important to hold it upside down, i.e. with the display facing downwards
and with the joystick facing upwards.
Synchronising two beds (double bed)
First press the RED button on the control unit on bed number 1 until it emits a double
audible signal and then release the button. Then press the RED button on the control unit on
bed number 2 until it emits four audible signals (2 x 2) end then release the button.
Make sure you keep the remote control vertical with the display facing downwards. Then
move the joystick to the left or the right on the remote control for bed number 1.
Use the menu on the remote control and select the icon
'+remote control' as shown in the illustration:
Follow the instructions shown in the display. While the text
is active, briefly press the RED button on the control unit of
bed number 2 and then release again.
The beds are now synchronised on the remote control.
If you want both beds to move in parallel, set both remote
controls to the 'double bed' icon as shown in the illustra-
tion: Please note that only the bed movements can be
synchronised.
NOTE: If, after the setting has been changed, the beds can be controlled in parallel but are
not in similar positions, you should lower the beds until they are parallel. It may be that the
beds do not operate in a completely synchronised way. This is not a manufacturing fault and
should not reduce the level of comfort.
Emergency function - Lower bed in the event of a power failure
In the event of a power failure you can lower the bed by pressing the red button on the
control unit and keeping it pressed until the bed is horizontal. However, you must have fitted
two 9 volt batteries into the bed's control unit. If you use this function, you must replace the
batteries to ensure that the function is available again in the event of another power failure.
NOTE: The emergency function for lowering the bed can also be used without a power
failure having occurred. This can be useful if you lose the remote control.