Jensen Dynamique Mode D'emploi page 8

To set up the bed's location
Turn the remote upside down (joystick pointing up). The
display will switch to standby.
Move the joystick up to move the head end up.
Move the joystick down to move the head end down.
Move the joystick to the right to move the foot end up.
Move the joystick to the left to move the foot end down.
Save your favourite mode by pressing the joystick down until
you see two (two second) flashes.
To return to the horizontal position press the joystick once.
To return to the saved position press the joystick once.
Tilt function
You can control both the head and foot end simultaneously
by double clicking the joystick (display pointing down). Then
press the joystick up or down to tilt the bed.
This enables you to adjust the head and foot end positions
independently.
If you press the joystick to the left or right, both the head
and foot of the bed will move up and down. Double click to
return to normal mode.
Music
Eleven songs have been pre-installed on the remote control.
Select the note symbol and press the joystick. Move the
joystick to the right to access an overview of the memory
card contents. A song will play for a few seconds if marked.
Press to select the song. The selected music will be used
for the alarm function.
You can save more music by using a card reader and a pc
and you can also arrange the music in file folders. You can
select 'mix' in a file folder to be woken by a random song
from the selected file folder.
The music is stored on a USD card which can be found
under the battery cover.
Any music you want to add must be in the following format:
8 bit, 44 kHz, mono. For this you can use the free
Wavosaur programme (www.wavosaur.com).
Select 'Tools->Batch processing'. Select the files to be
converted and then select the following functions: 'Convert
to mono 50% 50%', 'Convert to 8 bits', 'Convert to wav'
and then, if necessary, 'Normalize 0dB' to increase the
sound level. The sample rate is normally 44.1 kHz. However,
if the tempo is incorrect you can also select 'Re sample
44100Hz'. This programme allows you to convert music be-
fore you save it to the USD card. The selected format means
there is space for approx. 100 songs per GB. The USD card
supplied has a capacity of 1 GB.
8
Safety sensors
The Jensen Dynamique is fitted with safety sensors on both
sides of the base. These sensors reduce the risk of beco-
ming trapped between the bed's moving parts.
Whenever the sensors' infrared beam is interrupted, it will
only be possible to lower the bed when the path of the
beam is unobstructed again. If you try to lower the bed in
this situation, you will hear a peep. Once the path of the
beam is unobstructed you have to wait five seconds before
the bed can be lowered using the remote control.
WARNING: Even though a safety mechanism has been
incorporated to eliminate the risk of becoming trapped
between the bed's moving parts during normal use, there is
always a risk of injury if you do not use the bed correctly. We
therefore recommend you keep bodily parts away from the
mechanical sections of the frame when the bed is moving.
Strange noises
A mechanical and electrically adjustable bed generates
noise. In most instances, the amount of noise that the bed
makes depends on the acoustics of the room in which
the bed is situated. In the case of the massage function,
hard floors may cause resonance. This can be reduced by
placing a rug or another noise or vibration-resistant material
under the legs or wheels.
Upgrading software
The remote control and the control unit contain software
which can be upgraded. Jensen works continuously to
detect and rectify errors in the existing software and to
provide support for the new functions. New software can be
downloaded via http://www.jensen.no/softwareupdate
Usage
The bed's lifting motors are not designed for continuous
usage. Normally the motors should not operate for more
than 2 minutes during a 15 minute period. Any attempt
to exceed this degree of usage will reduce the life of the
product and may render the guarantee invalid. The bed has
been constructed in such a way that it can bear a maximum
weight of 150 kg, distributed equally between the head
end and the foot end. Any attempt to exceed this degree of
usage will reduce the life of the product and may render the
guarantee invalid.
Use with pacemakers
As is the case with all products that vibrate, there is a risk
that certain pacemakers will interpret the vibrations as body
movements. There is, therefore, a risk that this will affect
your pacemaker. If you are worried, please contact your
doctor.
Electrical data:
Input: 110-230V AC / 50-60 Hz / Max 85W
Standby power: 1W