Cleaning, Maintenance And Ordering Spare Parts; Disposal And Recycling; Storage - EINHELL GE-CR 30 Li Traduction Du Mode D'emploi D'origine

7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always pull out the safety plug before making
adjustments or carrying out maintenance,
cleaning and repair work on the equipment. Make
sure that the blade shaft is not turning.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
7.2 Replacing the cultivator blades
For safety reasons, we recommend having
the tiller blades replaced by an authorized
professional (see address on warranty certifi cate).
Warning!
Wear working gloves. Use only genuine spare
parts since otherwise the function and safety of
the machine cannot be guaranteed.
7.3 Maintenance
Ensure that all mounting components (i.e. screws,
nuts etc.) are always tightened so that the
equipment can be safely operated at all times.
Store the equipment in a dry room. All the metal
parts should be cleaned and then oil to ensure
that they provide a long life. For best results, clean
the plastic parts of the machine with a brush or
rag. Do not use any solvents to remove dirt.
For space saving storage undo the star nuts (Fig.
7,8/Item 8) and fold the push bar together as
shown in Fig. 16. Ensure that you do not damage
the cable. At the end of the season, perform a
general inspection of the equipment and remove
any deposits which may have accumulated.
At the start of each season, ensure that you
check the condition of the machine. If repairs are
necessary, please contact one of our customer
Anl_GE_CR_30_Li_USA_SPK7.indb 14 Anl_GE_CR_30_Li_USA_SPK7.indb 14
EN
service centers (see address on warranty
certifi cate).
7.4 Ordering replacement parts:
Service
1. If your power tool requires service,
contact an authorized Einhell USA dealer
or call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical
replacement parts should be utilized for
repairs. This will ensure that the safety of the
power tool is maintained.
2. If the battery charger cable is damaged, it
must be immediately replaced to avoid a
hazard. Contact the Einhell USA
service center at 1-866-EINHELL
(1-866-346-4355) for assistance.

8. Disposal and recycling

The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.

9. Storage

Store the equipment and its accessories out
of children's reach in a dark and dry place at
above freezing temperature. The ideal storage
temperature is between 41°F and 86°F
(5°C and 30°C). Keep the electric tool in its
original packaging.
The reprinting or reproduction by any other
means, in whole or in part, of documentation and
papers accompanying the products is strictly
subject to the express consent of iSC GmbH.
Subject to technical changes
- 14 -
customer
®
24.06.2019 11:08:29 24.06.2019 11:08:29