Before Starting The Equipment; Operation - EINHELL GC-SC 36/31 Li Traduction Du Mode D'emploi D'origine

3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before starting the equipment

Warning!
Always pull out the safety plug before making
adjustments or carrying out maintenance,
cleaning and repair work on the equipment.
The scarifi er is delivered unassembled. The
complete push bar must be assembled and
mounted before using the scarifi er.
Follow the operating instructions step-by-step
and use the pictures provided as a visual guide to
easily assemble the equipment.
Fitting the push bar holders (see Figs. 3
and 4)
Slide the push bar holders (Fig. 3/Item 7) into the
provided openings (Fig. 3) and fasten them with
the retaining screws (Fig. 4/Item 14)
Fitting the lower push bars (see Fig. 5)
•
Slide the lower push bars (Fig. 5/Item 6) onto
the push bar holders.
•
Screw the tubes together, using the screws
supplied (Fig. 5/Item 13).
There are 3 assembly holes so that the height
of the push bar can be adjusted to specifi c user
requirements at any time. Use the hole which is
best suited for you, making sure that you use the
same hole on both sides.
Fitting the upper push bar (see Fig. 6)
•
Push the upper push bar (Fig. 1/Item 5) such
that its holes line up with the holes of the
lower bar.
•
Use the two screws (Fig. 2/Item 13) to screw
the tubes together.
Anl_GC_SC_36_31_Li_USA_SPK7.indb 15 Anl_GC_SC_36_31_Li_USA_SPK7.indb 15
EN
•
Use the cable clips (Fig. 7a/7b) to attach the
power cable to the tubes of the push bars so
that it is possible to open and shut the ejector
flap.
Please ensure that the ejector fl ap can be opened
and closed easily!
Adjusting the scarifi er depth (see Fig. 9)
The scarifi er depth is adjusted at the two front
wheels using the adjustment mechanism. For this,
pull out the adjusting screw and turn the wheel to
the left or right into one of the available positions
(0/1/2/3).
The scarifi er depth must always be identically set
on both sides!
0 = drive/transport position
1 = scarifi er depth 0.11 in. (3 mm)
2 = scarifi er depth 0.28 in. (7 mm)
3 = scarifi er depth 0.35 in. (9 mm)
Installing the battery (Fig. 11-12)
Open the battery cover. This is done by pressing
the lock release (19) as shown in Fig. 11 and
swinging up the cover. Then slot the two batteries
into the mounts as shown in Fig. 12 and push
them forward until you hear the batteries engage.
Important!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on
the battery with the lower charge level. The two
batteries must always be fully charged before use.

6. Operation

Caution!
The scarifi er is equipped with a safety switch to
prevent unauthorized use. Immediately before
using the scarifi er, insert the safety plug (Fig. 12/
Item 15). Remove the safety plug again when
interrupting or terminating your work.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
- 15 -
28.01.2020 16:44:11 28.01.2020 16:44:11