Publicité
Les langues disponibles
Les langues disponibles
Introduction
To enjoy your new appliance as long as possible, please
read carefully the Operating Instructions and the attached
safety instructions before using it. Further, we recommend
keeping the Operating Instructions to recall the product
features in the future.
Within the continuous product development, we
reserve the right to make technical changes to
improve it.
This document represents translation of the original
Operating Instructions.
Supply includes
Take the appliance out of the transport package and check
it whether there are the following parts:
1 fretsaw
2 adapters
2 saw blades (1 saw blade being
preassembled)
1 saw blade cover
1 original Operating Instructions
Warranty Certificate
Please contact your dealer if any parts are missing or are
damaged.
Appliance + accessory equipment description (pic. A-
B+D)
1.
Strain screw
2.
Dust blowing hose
3.
Workpiece holder adjusting screw
4.
Saw blade cover
5.
Saw blade holder
6.
Saw blade
7.
Saw bench
8.
Feeder cable
9.
Dust extractor adapter
10.
Workpiece holder
11.
Copper tube for dust blowing
12.
Support
13.
Speed controller
14.
On/Off
15.
Bench adjustment scale
16.
Spare saw blade
17.
Saw blade adapter
18.
Mounting tool
19.
Saw bench stopping screw
20.
Saw bench insert
Technical specifications
Connection:
230 V ~ 50 Hz
Protection type:
IP 33
Max. output:
120W-S6/30%
Revolutions:
400-1,600 per min
Saw blade length:
128/133 mm
Cutting power 90°:
50 mm
Cutting power 45°:
27 mm
Bench size:
410x250 mm
Feeder cable:
2 m
Weight:
13 kg
General instructions
After unpacking, check all parts for any damage
during transport.
Check whether the shipment is complete.
Learn with the appliance functions using the
Operating Instructions before using it.
against stray current) 30mA only!
Use as designated
The fretsaw may only be used to cut angular pieces of
wood or wood-similar (plastic) workpieces.
Any other use will be considered a use in conflict with the
designation. The manufacturer will not be liable for any
consequential damage or injuries. Please be sure to know
that our appliances have not been designed for industrial
purposes.
Assembly
Fitting the saw to bench
To fit the saw, a massive-wood bench is better than a
weak compressed board where vibrations and noise
significantly affect your work.
Fixing materials necessary for assembly are not included
in the supply.
Example of fixing materials:
4 M8 hex screws
4 Ø 8 mm flat gaskets
4 Ø 8 mm washers
8 M8 hex nuts
Foam-rubber washer absorbing noise is also not included
in the supply. However, we strongly recommend using
such washer to reduce vibrations and noise. Rubber-foam
-1
(controllable)
washer specification: 450x250x13 mm.
Saw blade cover fitting
Loosen the nut on the saw blade cover and put the saw
blade on the saw head. The nut is self-locking.
Changing the saw blade (original saw blades)
Original accessory equipment and original wearable
and spare parts to be used only.
All covers and safety equipment must be properly
installed before putting the appliance into operation.
See the following points:
Appliance to be used with RCD (safety switch
Safety instructions
Follow all safety and warning instructions on the
appliance and keep them readable.
The safety equipment on the appliance must not be
disassembled or put out of operation.
Check the feeder cables. Do not use any defective
feeder cables. See Plugging.
Be caution when working: Risk of injury for fingers
and hands by the saw blade.
Any changeover, adjustment, measurement and
cleaning to be performed when the engine off only.
Unplug the appliance.
Any installation, repair and servicing of the wiring
may only be performed by professionals.
All protective and safety equipment must be
immediately refitted after finishing any repair and
servicing work.
Switch the engine off after leaving the place of your
work. Unplug the appliance.
Any changes to the appliance exclude the liability of
the producer for any consequential damage.
Clamping screw (pic. A/1) to be turned right to make
the saw blade (pic. A/6) loosen.
Lift off the saw blade cover (pic. A/4).
9
Publicité
