• Always keep the oven door closed when using the GRILL
GB
modes: This will achieve improved results while saving
energy (approximately 10%).
• Regularly check the door seals and wipe clean to ensure
they are free of debris so that they stick properly to the
door and do not allow heat to disperse.
Maintenance and care
Important: The appliance should be disconnected
from the mains supply before starting cleaning
operations.
To ensure a long life cycle for the appliance, it is essential
to carry out a thorough general clean frequently, while
observing the following instructions:
Inside the oven door:
Clean the surface with a cloth moistened with hot water and
non abrasive liquid detergent, then rinse and dry thoroughly.
Inside the oven:
• The inside of your oven is coated with a special self-
cleaning microporous enamel glaze which, at a normal
cooking temperature of between 200 and 300°C, oxidises
and completely eliminates all grease spots or other
substances that inevitably attack the inner walls of the
oven. This way, cleaning is kept right down to a minimum:
as a matter of fact, you just need to rub the surfaces of the
oven with a wet cloth regularly, after cooking, to remove
the thin layer of ash that may have been deposited during
cooking, in order to maintain the self-cleaning property
of the oven intact.
• After cooking where liquid has overflowed or when the dirt
has not been eliminated completely (for example when
grilling food, and the temperatures reached are not high
enough for the full self-cleaning action of the enamel to
be performed), we recommend you leave the oven on
at maximum temperature so that all grease residue and
the like are eliminated.
• If, after long-term use, you find evident grease stains
deposited on the self-cleaning oven walls, probably due
to your failing to follow the above maintenance advice,
clean the surfaces thoroughly with hot water and a soft
cloth (do not use any detergents), then rinse and dry
thoroughly.
• Do not remove any dry caked-on grease using sharp
objects, as these could etch the self-cleaning coating.
• If the self-cleaning surfaces inside the oven are damaged
or worn, due to incorrect or poor maintenance or after
many years of use, you can request a kit of self-cleaning
panels to line the inside of the oven. To order these, just
contact an authorised Service Centre.
Oven exterior:
• Only clean the appliance when the oven is cold.
• The steel parts and especially the areas with the screen-
printed symbols should not be cleaned with solvents or
abrasive detergents. It is advisable to use only a damp
cloth with lukewarm water and washing up liquid.
22
Stainless steel may remain stained if in long-term contact
with very calcareous water or aggressive detergents
(containing phosphorus).
It is therefore always necessary to rinse and dry all
surfaces thoroughly after cleaning.
Important: cleaning operations must be made
horizontally, in the direction of the steel glazing.
• After cleaning, any treatments to polish the surfaces may
be performed: only use specific products for stainless
steel.
Important: do not use abrasive powders, aggressive
detergents or acidic substances for cleaning.
Disassembling/assembling the oven door
To make it easier to clean the inside of your oven, the oven
door can be removed, by proceeding as follows:
• Open the door completely and lift the 2 levers "B";
• Now, shutting the door slightly, you can lift it out by pulling
out the hooks "A" as shown in figure.
To reassemble the door:
• With the door in a vertical position, insert the two hooks
"A" into the slots;
• Ensure that seat "D" is hooked perfectly onto the edge
of the slot (move the oven door backwards and forward
slightly);
• Keep the oven door open fully, unhook the 2 levers "B"
downwards and then shut the door again.
Replacing the oven light bulb
- Voltage 230 V
- Wattage 15 W
- Type E 14.
! Do not use the oven lamp as/for ambient lighting.
Make sure that the appliance
is disconnected from the
electricity supply.
U n s c r e w
t h e
g l a s s
protective cover from inside
the oven, unscrew the
lightbulb and replace it with
an identical one suitable for
high temperatures (300°C)
and with the following
characteristics: