Publicité
Les langues disponibles
Les langues disponibles
3 Applications
The colour camera and the power supply unit have
especially been designed for the use in video monitor -
ing systems. The camera has an automatic gain con-
trol (AGC) as well as an automatic electronic shutter
1
1
(
/
–
/
s). Furthermore, it is equipped with a
50
100 000
backlight compensation and an automatic white bal-
ance (range 2400 K up to 11 000 K). Due to the one-
cable technique, to connect camera and power supply
unit only one coaxial cable is necessary by which the
power supply and the video signal are transferred in
common.
The camera is weatherproof (IP 68) and can also
be used for outside applications. The power supply
unit must in any case be used indoors.
4 Mounting
1) Mount the supplied bracket [or, if desired, an other
bracket with 6.3 mm (
place.
2) Loosen the setscrew (8) of the bracket so that the
thread bolt (5) can freely be moved and screwed
into one of the two thread jacks (3) of the camera by
means of the knurled nut (6). If the picture repro-
duction is inverted after setting the camera into op -
er ation, the other thread jack must be used. Due to
the cylindrical form of the camera it is not possible
to see before which way round the camera has to
be mounted.
5 Setting into operation
1) For power supply, the camera requires a constant
current of 100 mA (also see label "Constant Current
100 mA" on the camera and the power supply unit).
When manufacturing the unit, this current has been
adjusted with the switches (13) on the power supply
unit. Prior to setting into operation check if the
switches are still in the correct position:
100mA
An incorrect adjustment may cause damage.
2) Connect the cable (4) of the camera to jack TO
CAMERA (15) of the power supply unit. The length
of the cable is 30 m. It can be extended up to 500 m
by using a high-quality cable:
Cable type
RG-58U
RG-59U
RG-6U
Up to 350 m the cable VCC-59 by MONACOR is
suitable as well.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
1
⁄
") thread] at the desired
4
Max. cable length
200 m
350 m
500 m
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
®
3) Connect the video output VIDEO OUT TO MONI-
TOR (14) of the power supply unit via a 75 Ω coax-
ial cable to the video input jack of the monitor or a
camera switcher resp. video splitter. Observe the
correct 75 Ω termination.
4) Plug the mains plug into a mains socket (230 V~ /
50 Hz) and switch on the power supply unit with the
POWER switch (10). The POWER LED (9) lights.
5) Switch on the connected monitor as well and align
the camera exactly to the monitoring range. If the
picture reproduction is inverted, mount the camera
by turning it 180°.
6) Screw off the screw sleeve (2) of the camera, and
adjust a clear picture by turning the lens (1).
Tighten the screw sleeve again.
6 Specifications
Image sensor: . . . . . . . . . 8.5 mm (
Colour system: . . . . . . . . . PAL
Synchronization: . . . . . . . hor. 15 625 Hz, vert. 50 Hz
Number of pixels: . . . . . . . hor. 537 × vert. 597
Resolution: . . . . . . . . . . . . 520 lines
Lens: . . . . . . . . . . . . . . . . 1 : 2.0 / 3.6 mm
Minimum illumination: . . . 0.01 lux
S / N ratio: . . . . . . . . . . . . . > 50 dB
Video output: . . . . . . . . . . 1 Vpp / 75 Ω
Protective class
of housing: . . . . . . . . . . . . IP 68
Ambient temperature: . . . -10 °C to +50 °C
Power supply: . . . . . . . . . 230 V~ / 50 Hz / 5 VA
Dimensions, weight
camera: . . . . . . . . . . . . ∅ 32 mm × 130 mm, 200 g
power supply unit: . . . . 106 × 44 × 96 mm, 600 g
Subject to technical modification.
GB
1
⁄
") CCD chip
3
7
Publicité
