RAVAK GLASSLINE GVS2 Instructions De Montage page 3

GB
ASSEMBLY INSTRUCTIONS
Two-part bathtub enclosure
The product is for mounting in a totally finished (tiled, plumbed, etc.) bathroom and fitted bathtub.
must only be fitted to a strong and rigid, solid bathroom wall that is vertical and adjacent walls should be square to each
other.
WARNING: when manipulating the glass panels, always ensure that some soft material is placed under the bottom edge,
for protection.
Assembly sequence:
1. Un-pack and prepare individual glass components according to the scheme for left (and right) variants. The glass for the fixed
glass wall is 8 mm thick and must be assembled with the maker's logo at the top and on the outer side. The fixed wall glass part has
two holes at the edge for the wall fixing brackets whilst the door side has 4 holes for the hinges. The door glass is 6 mm thick and
has two holes for the hinges, at the side meeting the fixed wall glass.
bottom but always readable from the outer side.
2. Fit the long plastic sealing profile to the vertical edge of the fixed glass wall on the side where it will contact the wall. For easier
manipulation, dampen the seal with a little soapy water. (Item 1). Onto the opposite edge of the fixed glass wall, fit the long soft
edged door seal. (Item 2)
3. Fit to the fixed glass wall, the dismantled halves of the hinges, the lower part of the hinges, with the side for the screw on the
inner side of the glass. Repeat with the upper hinge parts onto the folding door. Ensure that protection pieces are in place. Never fit
hinges directly metal to glass without the protection pieces.
4. On to the wall edge of the fixed glass wall, mount the wall brackets, angled side on the inner side, flat side on the outer side and
lightly tighten. The final tightening force after all adjustments are made should be 4-5 Nm torque.
5. According to the diagram 5, measure and mark points for drilling from the top of the bathtub up for the centre of the bracket
holes. The centres of the mounting brackets should be 60 mm from the outer edge of the bathtub. Insert the temporary white
moulded plastic parts under the glass wall so that it will have a 2 - 3mm space underneath for later filling. Ensure correct
measurements are maintained and that measurement points are vertical by a spirit level.
6. Drill 2 holes 8 mm dia. to depth of 60 mm. Fit the special 'Mungo' plastic wall plugs.
Warning: Be careful to avoid electric, water and gas pipes hidden beneath plasterwork or tiling.
7. Washers and screws are included for fitting components to traditional walls of brick and plaster or cement. If other wall materials
are used, other full strength fitting components must be utilised in accordance with manufacturers advice.
8. Set fixed glass wall vertical, fit and tighten the two 5 x 60 mm screws. For setting level to the base, adjust the white moulded
plastic parts, as necessary.
9. Adjust the door so that it is level. The gap between the door glass and the fixed glass wall must be even and approximately 4 mm
when the door is in the closed position. The soft seal will fill this space. When the product is correctly adjusted, it should have the
top edges of the glass panels level with each other and horizontal.
10. In the case of uneven walls or tiling, it is possible to make compensation by using the flexible mounting washer part underneath
the relevant wall bracket. (Diagram 8). The brackets must be in one vertical line and the gap between the upper and lower part of
the hinge must be the same for both hinges. The final gap under the fixed wall should still be 2 - 3 mm.
tightness of all connections. Tightening torque of glass against brackets or hinges should be 4 - 5 Nm.
11. Ensure the sealing profile between the fixed glass wall and tiled wall is pushed hard in. On to the lower edge of the door, fit the
bottom door seal.
12. Using the Ravak transparent silicon putty, fill all seals from the external side of the vertical connections between the fixed glass
wall and the tiling. Discard the temporary plastic pieces and fill the horizontal gap underneath the fixed glass wall. Place a knob of
silicon on top of the bracket screws and press into place the stainless steel bracket covers with the flat face outermost. When set,
remove the protective foil.
MAINTENANCE AND CLEANING - Do not overlook!
Maintenance and cleaning should only be carried out on painted and glass parts with soft non-abrasive cloths and cleaning liquids. Do not use any abrasive pastes,
wire wool or chemical cleaners e.g., thinners, acetone etc. The manufacturer is not liable for damage caused by wrong or careless use of cleaning materials.
The manufacturer recommends the use of the following Ravak products:
Anticalc glass layer. This layer is factory applied to all safety glass panels. Easy application-perfect results.
disinfecting effects-intended for versatile use in every household, also recommended for maintenance of bathtub hydromassage systems.
This high efficiency detergent has a pleasant fragrance. The product complements the series of specialized chemicals by RAVAK.
Provided that installation is carried out in a professional manner and in accordance with above schedule, the product is subject to 24 months warranty.
In alternative cases, local country or EU laws will prevail. The manufacturer is not liable for damage caused by incorrect installation, use or
maintenance.
For further information, contact your local Ravak dealer.
The manufacturer reserves the right to amend or improve on existing designs or features.
Please help preserve the environment by observing local country guidelines or laws regarding re-cycling. Materials which are not suitable for re-cycling must be
disposed of at an official and suitable waste control centre.
RAVAK a.s., Obecnická 285, 261 01 Pøíbram 1, ÈR tel.: 318 427 111, 318 427 200
fax: 318 427 269, 318 427 278, e-mail: smith@ravak.cz www.ravak.com
On this piece, the maker's logo can be at the top or the
RAVAK ANTICALC CONDITIONER -
GVS2
For best results, the product
DOUBLE CHECK
To be used for perfect maintenance of the protective
RAVAK DISINFECTANT - A solution with significant
RAVAK CLEANER -