S+S Regeltechnik AERASGARD RCO2-W Notice D'instruction page 6

G
®
AERASGARD RCO
The maintenance-free microprocessor-controlled room sensor AERASGARD
CO content of the air within a range of 0...2000 ppm. The measurement value is converted into standard signal of 0 -10 V.
2
The maintenance-free microprocessor-controlled room sensor AERASGARD
switches) is used for detecting the CO
standard signal of 0 -10 V or 4...20 mA. Optional with traffic light indicator (five coloured LEDs).
Elegant enclosure made of plastic, with snap-on lid, based with 4-hole attachment, for installation on vertically or horizontally installed flush-
mounted boxes, with predetermined breaking point for surface- mounted connection or in enclosure made of stainless steel (top and bottom parts
are stainless steel, the cover is screwed on), vandal-proof version e.g. for schools, barracks and public buildings.
The CO content of the air is measured using an optical NDIR sensor (non-dispersive infra-red technology). The detection range of the CO
2
sensor is calibrated for standard applications such as monitoring residential rooms and conference rooms. Room ventilation on an as-needed
basis, improved well-being and customer benefit, increased comfort as well as reduced operating costs through energy conservation.
TECHNICAL DATA
Power supply:
Power consumption:
Sensor:
Measuring range:
Output:
Relay output:
Measuring accuracy:
Temperature dependence:
Pressure dependence:
Long-term stability:
Gas exchange:
Ambient temperature:
Warm up time:
Response time:
Electrical connection:
Enclosure:
Dimensions:
Installation:
Protection class:
Protection type:
Standards:
Optional:
®
AERASGARD RCO - SD Room CO
2
®
AERASGARD RCO - W Room CO
2
Type ⁄ WG02 Measuring Range
CO
2
RCO - SD (fixed)
2
R C O 2 - S D - U 0...2000 ppm
RCO - W (switchable)
2
R C O 2 -W 0...2000 ppm ⁄ 5000 ppm
RCO2-W VA 0...2000 ppm ⁄ 5000 ppm
RCO2-W DISPLAY 0...2000 ppm ⁄ 5000 ppm
RCO - W - A (switchable)
2
R C O 2 -W- A 0...2000 ppm ⁄ 5000 ppm
A = with "traffic light" (five coloured LEDs) for displaying the CO
Note: This unit must not be used as safety-relevant device!
- W ⁄ RCO - SD
2 2
content of the air within a range of 0...2000 ppm or 0...5000 ppm. The measurement value is converted into
2
24 V AC ⁄ DC (± 10 %)
< 1.5 W ⁄ 24 V DC typical; < 2.9 VA ⁄ 24 V AC typical; peak current 200 mA
Optical NDIR sensor (non-dispersive infra-red technology),
with manual calibration (via zero button),
RCO - SD with automatic calibration (fixed)
2
RCO -W
with automatic calibration (can be deactivated via DIP switches)
2
RCO - SD 0...2000 ppm (fixed)
2
RCO - W 0...2000 ppm or 0...5000 ppm (selectable via DIP switches)
2
RCO - SD 0 -10 V (fixed)
2
RCO - W 0 -10 V or 4...20 mA, working resistance < 800 Ω (selectable via DIP switches),
2
with offset potentiometer (± 10 % of the measuring range)
RCO - SD
without changeover contact
2
RCO - W with potential-free changeover contact (24 V / 1 A)
2
typically ± 30 ppm ± 3 % of measured value
± 5 ppm ⁄ °C or ± 0.5 % of measured value ⁄ °C (whichever is higher)
± 0.13 % ⁄ mm Hg
< 2 % in 15 years
by diffusion
0...+ 50 °C
approx. 1 hour
< 2 minutes
0.14 - 1.5 mm 2 , via screw terminals
plastic, material ABS, colour pure white (similar to RAL 9010), stainless steel enclosure optional V2A (1.4301)
85 x 85 x 27 mm (Baldur 1)
100 x 100 x 25 mm (stainless steel)
wall mounting or on in-wall flush box, Ø 55 mm, base with 4-hole for mounting on vertically or
horizontally installed in-wall flush boxes for cable entry from the back, with predetermined
breaking point for on-wall cable entry from top ⁄ bottom in case of plain on-wall installation
III (according to EN 60 730)
IP 30 (according to EN 60 529)
CE conformity, electromagnetic compatibility according to EN 61 326, EMC Directive 2014 ⁄ 30 ⁄ EU,
Low Voltage Directive 2014 ⁄ 35 ⁄ EU
with traffic light indicator (five coloured LEDs, see table) for displaying the CO
with display (see AERASGARD
sensor and measuring transducer, Standard
2
sensor and measuring transducer, Premium
2
Output
CO
2
(fixed)
0 -10 V
(switchable)
0 -10 V ⁄ 4...20 mA
0 -10 V ⁄ 4...20 mA
0 -10 V ⁄ 4...20 mA
(switchable)
0 -10 V ⁄ 4...20 mA
® RCO - SD with automatic calibration (fixed) is used for recording the
2
®
RCO - W with automatic calibration (can be deactivated via DIP
2
® RFTM-LQ-CO
) for displaying the actual CO
2
Equipment
–
Changeover contact
Changeover contact, stainless steel enclosure
Changeover contact, display
Changeover contact, LEDs
concentration.
2
Rev. 2019 - V32
concentration
2
content in ppm
2
Display Item No.
(Baldur 1)
15 01-61A 0- 1001-2 00
1501- 61A0 -7301- 200
1501- 61A0 -7301- 205
■ see RFTM-LQ-CO
2
with traffic light
1501- 61A0 -7331- 200
2