Publicité
Les langues disponibles
Les langues disponibles
c) Gene
eral
•
Ma
ke sure there is
coo
oling.
•
Hav
ve a qualified e
•
Co
nnect the devic
gro
ounded switched
or
dimmer channe
•
The
e installation ha
•
To
adjust the focu
des
sired focus and
7. Op
eration
Refer to t
the illustrations
•
The V
VDPL110CC ca
man
ual mode or D
Sound
controlled m
•
Set
t DIP switch 10
•
Set
t the microphon
Automa
atic mode
•
Set
t DIP switches 7
•
Set
t the colour cha
Slave m
mode
•
Co
nnect multiple V
•
Set
t the master VD
•
Set
t DIP switch 1 t
Manual
l mode (fixed
•
Set
t DIP switches 8
Note
e: switch 7 is no
DMX co
ontrolled mo
•
Set
t DIP switch 10
•
All
DMX-controlled
sig
nals. This digita
the
e DMX controller
ind
dividual address
•
Wh
hen all devices h
par
rticular channel
sim
multaneously. If
num
mber. Changing
•
In
case of the 7-ch
(CH
H1~7), the seco
•
Use
e the DIP switch
•
Ref
fer to the table
17.01.20
011
s no flammable
material within
lectrician carry
out the electric
e to the mains w
with the power
d circuit and can
nnot be run off
el is used solely
for 0% to 100%
as to be approve
ed by an expert
s of the beam r
release both slid
tighten the kno
obs.
s on page 2 of th
his manual.
an operate in fiv
ve modes: soun
DMX controlled
d mode.
mode
to the ON posit
tion to enable so
ne [5] sensitivit
ty with the sens
7, 9 and 10 to O
ON to enable au
anging speed wi
th switches 1 to
VDPL110CC's a
as described in
DPL110CC to so
ound controlled
o ON to enable
slave mode.
d output)
8, 9 and 10 to O
ON to enable ma
D
DIP switch
1, 2 ON
3, 4 ON
5, 6 ON
ot used.
de
to the OFF pos
ition to enable D
d devices need a
a digital start ad
al start address
is the channel n
r. The same sta
arting address ca
can be set for
every device.
have the same a
address, all the
. In other words
s: changing the
you set individ
ual addresses, e
g the settings of
f one channel w
hannel VDPL11
10CC, you will h
ond unit to 8 (1
+ 7) (CH8~14)
hes to set the a
ppropriate DMX
switch
value
below for an ov
verview of the c
VDPL11
10CC
a 50cm radius
al connection.
plug. All fixture
a rheostat or di
% switch.
t before the dev
der-knobs at the
nd controlled,
ound controlled
sitivity knob [6]
tomatic mode.
o 6.
§6.b.
or automatic m
anual mode.
output
red LEDs
green LEDs
blue LEDs
DMX controlled
ddress so that t
number from w
an be used for a
units will "listen
settings of one
each device will
will only affect th
have to set the s
), the third to 1
X address.
1
2
2
3
4
1
2
2
4
8
ontrol signals p
5
of the device an
nd there is suffi
es must be powe
ered directly off
immer circuit, e
even if the rheos
vice is taken into
o service.
e bottom of the
device. Set the
automatic mo
ode, slave mod
mode.
].
mode.
mode.
he correct devic
ce responds to t
hich the device
starts to "listen
a whole group o
of devices or an
n" to the contro
ol signal on one
e channel will af
ffect all devices
"listen" to a se
eparate channel
he device in que
estion.
start address of
f the first unit to
5 (8 + 7) (CH1
5~21), and so o
5
5
6
7
8
8
9
1
6
32
64 12
28 256
er channel.
Re
ev. 01
cient
f a
stat
e
de,
the
n" to
o 1
on.
man nv
©Vellem
Publicité
