Publicité
Les langues disponibles
Les langues disponibles
Safety
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury.
warns about hazards that will cause seri-
ous personal injury, death or major property damage if
ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which
are important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
DESCRIPTION
This non-corrosive pump, with reversible flow direction,
is designed to pump water only.
Risk of fire or explosion. Can cause severe
injury, property damage or death. Do not use in explo-
sive atmospheres. Pump water only with this pump.
SPECIFICATIONS
Liquid Temp. Range ........... 35° to 120° F (1.7° to 50° C)
NOTICE: Never operate the pump for more than two
hours at a time. Never run the Blue Water Pump dry!
NOTICE: This unit is not designed for applications involv-
ing salt water or brine! Use with salt water or brine will
void warranty.
PERFORMANCE
GPM (LPM) AT TOTAL FEET (M)
Model
0
10
No.
(0)
(3m)
CAPACITY GALLONS(L)/Minute
BW8512
10
8.5
BW85P
(37.9)
(32.2)
EBW85-I
DC MOTORS
1. DC motors must be connected to a fully charged
automotive, tractor or marine type battery of the
proper voltage.
2. Life expectancy of the motor is 500 to 1000 hours.
For more information, see your retailer, or call Simer
customer service at 1-800-468-7867.
For parts or assistance, call Simer Customer Service at
20
30
40
(6.1m) (9.1m) (12.2m)
6.8
4.4
1.5
(25.7)
(16.6)
(5.7)
GENERAL SAFETY INFORMATION
1. This equipment is only for use with an automotive,
tractor or marine type battery fully charged to 12
Volts DC.
Hazardous electrical current. Battery
current can cause severe burns and start a fire if the
battery is short circuited.
2. Know the pump application, limitations, and poten-
tial hazards.
3. Do not use in water where fish are present.
4. Release all pressure within the system before servic-
ing any component.
5. Drain all water from the system before servicing.
6. Secure the discharge line before starting the pump.
An unsecured discharge line can whip, possibly
causing personal injury and/or property damage.
7. Check hoses for weak or worn condition before each
use, making certain all connections are secure.
8. Periodically inspect the pump and system compo-
nents. Keep free of debris and foreign objects.
Perform routine maintenance as required. See the
Maintenance Section.
9. Provide a means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
10. Personal Safety:
a. Wear safety glasses at all times when working
with the pumps.
b. Keep work area clean, uncluttered and properly
lighted.
c. Keep visitors at a safe distance from the work
area.
d. Make the workshop child-proof – with padlocks,
master switches, and by removing starter keys.
11. When wiring a DC pump, follow all of the electrical
and safety codes that apply.
12. All wiring is to be 12 gauge stranded copper wire
that is:
A. Water resistant
B. Oil resistant
C. Flame resistant
NOTICE: This pump is equipped with a Permanent
Magnet Type 12 Volt Reversible DC motor. Be sure it
is connected properly as illustrated for the direction
of flow indicated by the arrows on the pump case
(see Figure 1, Page 4).
13. Use insulated crimp type connectors.
14. Protect the electrical wires from sharp objects, hot sur-
faces, oil, and chemicals. Avoid kinking the wires.
Replace or repair damaged or worn wires immediately.
1-800-468-7867 / 1-800-546-7867
3
Publicité
