Use Of The Included Valve Adapters; Care And Maintenance; Maintenance - EAL APA 16540 Manuel De L'opérateur

Verriegeln Sie den
Ventilanschluß
Lock the
valve connector
Fig. 4
To infl ate, switch the compressor on with the on-off
switch.
The manometer (position 9 in the overview) is used for
the general inspection of the air pressure. Once you
have reached the desired air pressure, switch off the
compressor. Remove the valve connector in reverse order
(fi gures 5 – 2).
During the fi lling process, always ensure
that the air pressure is correct (refer to the
operating instruction of your vehicle for this).
The compressor can provide a pressure of up
to 18 bar. There is a risk of explosion and injury
if the pressure is too high.
Never let the compressor work longer than
10 minutes at a time as there is a risk of
overheating. Switch the compressor off after
10 minutes and let if cool off before you put it
back into operation.
Never let the compressor run unsupervised.
After fi lling a tyre, check the tyre pressure one more time
with a separate air pressure gauge (e.g. at the petrol
station, car workshop).

6.4.2 USE OF THE INCLUDED VALVE ADAPTERS

(Position 14 in the overview)
A Bicycle valve adapter
(for Dunlop and Sclaverand valves)
B Adapter for balls
C Universal adapter for leisure articles
(infl atable pool toys, etc.)
10
Sie können jetzt
den Reifen mit dem
You can now start
Kompressor
to infl ate the tyre
befüllen
Fig. 5
Fig. 6: Valve adapter
A Bicycle valve adapter
(for Dunlop and Sclaverand valves):
For Sclaverand valves: Unscrew the knurled screw of the
valve tappet and press it briefl y down once.
Screw the valve adapter with the knurled rim down onto
to bicycle valve.
Now connect the air hose to the bicycle valve adapter as
shown on fi gures 2 – 5. Now you can fi ll the bicycle tyres
by switching on the compressor. Once you have reached
the desired air pressure, switch off the compressor. Re-
move the valve connector in reverse order (fi gures 5 – 2).
Unscrew the bicycle valve adapter from the bicycle valve.
Für Sclaverandventile: Retighten the knurled screw of the
valve tappet.
B Adapter for balls
Open the lock of the valve connection (fi gure 2). Place the
adapter for balls in the valve connection. Lock the valve
connection (fi gure 3). Place the adapter into the valve of
the balls. Now you can infl ate the ball by switching on
the compressor. Once you have reached the desired air
pressure, switch off the compressor. Remove the adapter
from the valve connection by proceeding as described
above in reverse order.
C Universal adapter for leisure articles
Open the lock of the valve connection (fi gure 2). Place
the universal adapter in the valve connection. Lock the
valve connection (fi gure 3). Place the universal adapter in
the fi lling point of your leisure article. Depending on the
mode, the universal adapter may have to be held while
you are infl ating the object. Now you can start infl ating
by switching on the compressor. Once you have reached
the desired air pressure, switch off the compressor. Remo-
ve the adapter from the valve connection by proceeding
as described above in reverse order.

7. CARE AND MAINTENANCE

7.1 MAINTENANCE

Store the power pack at room temperature. If the power
pack is not used for longer periods of time, recharge it in
the winter every two months and once a month in the
summer.
Changing the fuse on the 12 V car charger cable:
Turn the knurled screw at the tip of the 12V plug
counter clockwise until it is disconnected from the plug and
remove it. The fuse is released and can be pulled out from
the plug. Replace it with a new fuse of the same strength
and screw the knurled screw back into the plug.
Fuse 6.0 x 30 mm, F, 2 A, 250 V