Publicité
Les langues disponibles
Les langues disponibles
Initial star
Initial star
Initial star
Initial startup
Initial star
GB GB
GB GB
GB
After checking that the unit has been installed cor-
rectly and after inspecting the current, water and
waste water (according to DIN 1988, part 4), start
the unit as described below:
Undo the childproof lock (11
Run the cable of the transformer plug (1 1 1 1 1 ) through
the connection cable gland (10
®
Bewados
module and connect to the terminal A A A A A
(polarity is not important).
Plug the transformer plug (1 1 1 1 1 ) into the outlet.
pears on the display, and an audio signal is emit-
ted. These signals indicate that there is no active
substance in the unit.
Connecting the active substance container
Connecting the active substance container
Connecting the active substance container
Connecting the active substance container
Connecting the active substance container
® ® ® ® ®
Be
Be
Be
Bew w w w w ados
Be
ados
ados
ados
ados
module
module
module
module E3
module
1. Undo the childproof lock (11
cap (7 7 7 7 7 ).
2. Remove the aluminium seal from the 3kg min-
eral substance container.
3. Lift the active substance container from the bot-
tom above the suction pipe (8 8 8 8 8 ) and attach it by
turning it gently. The empty message goes out,
and the audio signal is switched off.
4. Flip down the cap (7 7 7 7 7 ) and screw down the child-
proof lock (11
11
11
11) to prevent the mineral substance
11
container from twisting.
Connect the water flow. The metering unit is now
ready to use.
Be
Be
Bew w w w w ados
ados
ados
® ® ® ® ®
module
module
Be
Be
ados
ados
module
module E10/E20
module
1. Undo the childproof lock (11
cap (7 7 7 7 7 ).
2. Connect the suction line (13
(14
14
14
14) of the suction lance. The suction line is
14
marked for suction. It must be pushed onto the
nozzle with the arrow pointing inside the unit.
The return line is connected to the other noz-
zle. Secure both lines using the hose clamps
provided.
3. Insert the plug (12
the socket (B B B B B ) of the electronic controller (5 5 5 5 5 ).
4. Flip the cover (7 7 7 7 7 ) back down and screw down
the childproof lock (11
14
14
14
14
14
tup
tup
tup
tup
11) and flip up the cap (7 7 7 7 7 ).
11
11
11
10) on the rear of the
10
10
10
E3
E3
E3
E3
11
11
11) and flip up the
11
E10/E20
E10/E20
E10/E20
E10/E20
11
11
11) and flip up the
11
13
13) and the return line
13
13
12
12
12
12) of the suction lance (9 9 9 9 9 ) into
11
11
11
11).
5. Open the 10/20l box or canister of active sub-
stance. Remove any aluminium seals. Insert the
suction lance (9 9 9 9 9 ) into the container and tighten
the lid.
Do not lift or tr
Do not lift or transpor
Do not lift or tr
Do not lift or tr
Do not lift or tr
suction lance handle
suction lance handle. . . . .
suction lance handle
suction lance handle
suction lance handle
Connect the water flow. The metering unit is now
ready to use.
Corrosion protection in copper pipes with
Corrosion protection in copper pipes with
Corrosion protection in copper pipes with
Corrosion protection in copper pipes with
Corrosion protection in copper pipes with
Be
Be
Bew w w w w ados
ados
ados
ados
® ® ® ® ®
module E20 and Quantophos
module
module
Be
Be
ados
module
module
ap-
The objective of the procedure is to maintain wa-
ter with a pH value between 7.8 and 8.4.
The factor on the electronic controller may need
to be reprogrammed:
First, begin metering using the factory setting (f f f f f ac-
tor 12
tor 12
tor 12
tor 12). Remove approximately 100 litres of water
tor 12
from the system downstream from the metering
unit and upstream from any storage containers.
Next, collect approximately 2 litres of water in a
clean container and measure the pH using a pH
metre.
If the measured pH is less than 7.8
m m m m m ust be mo
ust be mo
ust be mo
ust be mov v v v v ed to
ed tow w w w w ards
ed to
ed to
ust be mo
ed to
= 1 metering stroke).
If the measured pH is greater than 8.4
tor m
tor m
tor must be mo
ust be mo
ust be mo
ust be mov v v v v ed to
tor m
tor m
ust be mo
tre pulses = 1 metering stroke).
Hold down
Hold do
Hold do
wn
wn the T1 and T2 keys simultaneously for
wn
Hold do
Hold do
wn
around 2.5 seconds to change the factor. The dis-
play reads "12" (factory setting).
T1 and
T1 and
T2
T2
Use the T1 and
T1 and
T1 and T2
T2 keys to select the required fac-
T2
tor between "1" and "15".
Next, hold down the T1 and
ously f
ously f
ously f
ously f
ously for around 2.5 seconds
or around 2.5 seconds
or around 2.5 seconds
or around 2.5 seconds
or around 2.5 seconds. The new factor is
stored and the controller returns to normal opera-
tion.
Keep measuring and changing the setting until the
measured pH is between 7.8 and 8.4. Flip the
cover back down and tighten the screws on the
childproof lock.
anspor
ansport the canister b
anspor
t the canister by the
t the canister b
t the canister b
anspor
t the canister b
E20 and Quantophos
E20 and Quantophos
E20 and Quantophos
E20 and Quantophos
is less than 7.8
is less than 7.8, the factor
is less than 7.8
is less than 7.8
ards
ards
ards "1"
"1"
"1"
"1" (1 water metre pulse
ards
"1"
greater than 8.4
greater than 8.4
greater than 8.4, the fac-
greater than 8.4
ed to
ed tow w w w w ards
ed to
ards "15"
ards
ards
"15"
"15" (15 water me-
"15"
ed to
ards
"15"
T1 and
T1 and
T1 and T2 k
T2 ke e e e e ys sim
T2 k
T2 k
ys simultane-
ys sim
ys sim
T1 and
T2 k
ys sim
y the
y the
y the
y the
® ® ® ® ®
Cu2
Cu2
Cu2
Cu2
Cu2
ac-
ac-
ac-
ac-
factor
factor
factor
factor
fac-
fac-
fac-
fac-
ultane-
ultane-
ultane-
ultane-
Publicité
