Installation - Femi 911 Mode D'emploi Et Entretien

– When in need, only use approved power supply cable
extensions.
– Beware of electrification: avoid all contact with earthed
objects such as pipes, radiators and refrigerators.
1.6 SAFETY PROCEDURE FOR FURTHER RISKS
– Do not force the machine unnecessarily: excessive
cutting pressure may lead to rapid deterioration of the
blade and a decrease in performance in terms of finish
and cutting precision.
– When cutting aluminium and plastics always use the
appropriate clamps: all workpieces must be clamped
down firmly.
– Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
– Always use the tools recommended in this manual to
obtain the best results from your cutting-off machine.
– Always keep hands away from the work area when the
machine is running; before performing tasks of any
kind release the main switch button located on the
handgrip, thus disconnecting the machine.
– Always keep hands away from the work area when the
machine is running; before performing tasks of any
kind release the main switch button located on the
handgrip, thus disconnecting the machine.
1.7 NOISE CONDITIONS
Idling
Equivalent sound level ............................ Leq = 75 dB(A)
Running with full load
Transverse cutting of hard wood (maple wood) mm.50x80
Equivalent sound level ......................... Leq = 81,7 dB(A)
Cutting of section aluminium 40x40 mm. thickness 2 mm.
Equivalent sound level ......................... Leq = 89,1 dB(A)
Average sound level ........................... Lpm = 82,7 dB(A)
Environmental correction factor ................ K = 3,9 dB(A)
Normalized sound power ....................... Lwa = 97,4 dB(A)
These tests were performed with a standard blade Z=48 to
cut wood and with a special blade Z=96 to cut aluminium,
always with the machine positioned on the work bench.
The frequency root mean RMS weighed for hand-arm
acceleration does not exceed 2.5m/s².
NOTE:
Measurements were obtained in compliance with
UNI 7712, ISO 3740, ISO 3746 and ECC 89/392
rules.
When cutting aluminium the use of protective
earphones or ear plugs is absolutely necessary.
The use of this gear is also recommended for all
other uses.
10
1.8 INFORMATION ABOUT THE
ELECTROMAGNETIC COMPATIBILITY
The European regulations on safety and, in particular, the
EEC Directive 89/336 contemplate that all the equipment
be equipped with shielding devices against radio
interferences both from and towards the outside.
This machine is safe and in compliance with above
regulations.
Tests were carried out according to EN 55011, EN 50081-
1, regulations.
1.9 MACHINE DESCRIPTION (Fig. 1)
The mitre-saw machine consists of three basic parts : the
machine body complete with motor 6 which is integrated
into lower part 3 by means of the joint 4 and the swivel
support 5, and the upper work unit consisting of the work
table 15, the rest square 17 and the movable blade cover
16.
The base 3 is used as rest when cutting and butting
operations have to be carried out in the different available
angles; the upper table is used as rest when trimming or
sectioning wood tables of huge dimensions and, in particular,
when cutting wood along grain.
Legend Fig. 1
1 - Control handgrip
2 - Main switch start button
3 - Base
4 - Body/base swivel joint
5 - Rotating bearing
6 - Motor
7 - Blade
8 - Lever to unblock graduation
9 - Button to unblock body descent
10 - Permanent blade shield
11 - Movable blade shield
12 - Bar clamp shaft
13 - Dust exhaust manifold
14 - Workpiece clamps (optional)
15 - Upper work surface
16 - Movable upper safety guard
17 - Bearing bracket
18 - Support feet
19 - Transport locking pin
51 - Main switch locking device
52 - Main switch release device
2

INSTALLATION

2.1 REMOVAL OF PACKAGING
Remove the box used to protect the machine during
transportion and keep it intact for future transportation and
storage.
2.2 HANDLING
This mitre-saw is small and light and, therefore, can be
easily handled by one person alone by locking the
transportation block by means of the pin 19 and by lifting
the machine by means of the control handgrip 1.