Metabo PWE 11-100 Notice Originale page 14

en ENGLISH
6.5 Water connection
Regularly check that the shut-off cock, hoses,
seals and connection pieces are functioning
correctly.
Use only clean tap water. The water pressure
must not exceed 6 bar.
Only use the machine when it properly
connected to the water supply.
Do not allow water within the vicinity of the
machine or close to people in the working
area.
Always position the machine so that no water
can enter the machine or come in contact with
electrical components.
- Ensure that the shut-off cock (1) is closed.
- Ensure that the water tap to the water supply is
closed.
- Fit a water hose (1/2 inch or 13mm ) with a
standard self-locking quick connector to the
connection piece (2) until it locks into place.
- Open the water tap to the water supply.
To remove the hose, close the water tap to the
water supply and then open the shut-off cock
(1) to release the pressure in the hose. When
removing the hose, make sure that no water enters
the machine. Close the shut-off cock (1).
6.6 Fitting/Removing the accessory
Press in the spindle locking knob (11) only
when the spindle is stationary!
To fit:
- Press in the spindle locking button (11) and turn
the spindle (8) by hand until you feel the spindle
locking button engage.
- Manually screw on the support plate (18) (with
velcro-type fastening), turning clockwise.
- Simply press the polishing disc (17) (with velcro-
type fastening) so that the polishing disc (17) and
support plate (18) are perfectly aligned.
To remove:
- Press the spindle locking button (11).
- Manually unscrew the support plate (18), turning
anticlockwise (apply a flat wrench to the spanner
flat of the plate if necessary).
7. Use
7.1 Setting speed
The speed can be preset via the setting wheel (19)
and is infinitely variable.
Positions 1-6 correspond approximately to the
following no-load speeds:
1 ........ 1700 / min
2 ........ 2700 / min
3 ........ 3500 / min
The VTC electronics make material-compatible
work possible and an almost constant speed, even
under load.
7.2 Switching On and Off
Switch on first, then guide the accessory
towards the workpiece.
14
4....... 4100 / min
5....... 4800 / min
6....... 5400 / min
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
To switch on: Connect the machine to the power
supply. Push the RESET button (6). Push the
sliding switch (12) forward. For continuous
activation, now tilt downwards until it
engages.
Switching off: Press the rear end of the slide
switch (12) and release.
7.3 Working instructions
To start work:
- Set up the water connection (see chapter 6.5)
- Test the GFCI (see chapter 6.3).
- Open the shut-off cock (1): water flows from the
spindle (8).
- If necessary, adjust the speed. Switch on the
machine.
- Fit the accessory on the tool.
- Apply moderate pressure on the machine and
move it to and fro across the surface.
To finish work:
- Remove the accessory from the tool.
- Switch off the machine and allow it to come to a
standstill.
- Close the shut-off cock (1).
- Store away the machine.
8. Troubleshooting
The pilot light (7) does not go out when the
TEST button (5) is pressed. Unplug. You must not
use the machine! Have a qualified electrician check
the machine.
Restart protection When power is restored after a
power failure, the machine - which is still switched
on - will not start for safety reasons. Push the
RESET button (6). The pilot light (7) now lights up.
The GFCI (4) switches off the machine
repeatedly when it is turned on. Unplug. You
must not use the machine! Have a qualified
electrician check the machine.
The electronic signal display (13) lights up and
the load speed decreases. The coil temperature
is too high! Run the machine in idling until the
electronics signal indicator switches off.
9. Cleaning, Maintenance
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,