Festool CS 70 ST 650 Notice D'emploi page 7

1 Scope of delivery [Fig. 1]
[1-1] Guide unit consisting of:
2 guide rods mounted on 2 supports
[1-2] 1 Open-end spanner size 15
[1-3] 1 Open-end spanner size 10
[1-4] 1 Allen key 5 mm
[1-5] 1 Adjusting bracket, front
[1-6] 4 Bolts M6x16
[1-7] 4 Washers Ø 6
[1-8] 4 Bolts M8 x 25
[1-9] 2 Fitting angle
[1-10] 4 Square nuts
[1-11] 1 Washer 4 mm thick
(this washer is only needed as a compen-
sating washer when extension tables and
sliding table are fitted)
[1-12] 1 Adjusting bracket, rear
[1-13] Complete table, consisting of: aluminium
profile plate with fitted roller supports
with guide rollers and scraper
2 Technical data
Dimensions
Width:
Length:
Max. slide travel:
Max. cutting length:
3 Fitting the sliding table
The sliding table is mounted on the left of the
PRECISIO.
Proceed as follows:
• Attach one fitting angle [2-3] each onto the front
and rear of the table frame of the PRECISIO
[Fig. 2]. Insert a square nut [1-10] into the cor-
responding square hole beneath the saw table
for the fastening bolt lying towards the middle
of the table.
- Place bottom side of fitting angle [2-3] on the
rib [2-4] on the table frame and screw in place
with bolt [2-5].
- The nut for the second fastening bolt is stuck
to a strip as an assembly aid. First insert a nut
from the front into the lateral opening [2-1] and
screw in bolt.
- Then remove strip and insert second nut into
the rear opening and screw rear fitting angle in
place.
• Attach the front and rear adjusting brackets [5-
1] to the carrier [5-5] using 2 screws [5-4] and
washers [5-6] with the mounting lobes [5-3]
facing inwards [Fig. 5]. Adjusting brackets and
support must lie against one another following
assembly, do not tighten bolts yet.
• Suspend entire guide unit (rods) by suspension
lugs in the notches in the fitting angles [2-3,
1-9] [Fig. 3].
• Push the head of the carriage bolt [5-2] through
the slots [2-2] in the frame, push bolt down and
tighten slightly with handle [3-1].
• Check that the supports rest on the adjusting
bolts [3-3] at the front and rear.
• To prepare for insertion of the sliding table:
- Fully open clip at rotary knob [4-5].
- Locate scraper [4-6] in correct position (bottom
edge parallel to guide rod).
• Place sliding table on the inner guide rod from
the front at a steep angle (almost vertical) [Fig.
4] so that the guide rod is between the roller
[4-4] and ball bearing [4-3].
• Fully insert sliding table and tilt into working
position (onto second guide rod).
250 mm • The sliding table can be locked with the rotary
335 mm knob [4-5].
865 mm
650 mm
4 Adjusting the table height
A correctly adjusted sliding table is approx. a
paper thickness higher than the table area of the
basic table.
4.1 Checking the table height
• Fit angle fence on sliding table.
• Move stop guide so that it projects by approx.
20 mm over the base table.
• Check the gap between the tabletop and stop
and determine the amount of correction.
4.2 Adjusting the table height
A separate adjustment must be carried out at the
front and rear support.
• Loosen counternut [3-4]
• Set correct height and adjusting screw [3-3].
• Re-tighten counternut [3-4] and fastening bolt
[5-4].
7