Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
E N G L I S H
Mains plug replacement (U.K. & Ireland
only)
•
Should your mains plug need replacing and you are
competent to do this, proceed as instructed below.
If you are in doubt, contact an authorized BERNER
repair agent or a qualifi ed electrician.
•
Disconnect the plug from the supply.
•
Cut off the plug and dispose of it safely; a plug with
bared copper conductors is dangerous if engaged in
a live socket outlet.
•
Only fi t 13 Amperes BS1363A approved plugs fi tted
with the correctly rated fuse (1).
•
The cable wire colours, or a letter, will be marked
at the connection points of most good quality plugs.
Attach the wires to their respective points in the plug
(see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
•
Before replacing the top cover of the mains plug
ensure that the cable restraint (3) is holding the outer
sheath of the cable fi rmly and that the two leads are
correctly fi xed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires
to the earth pin marked E or
For 115 V units with a power rating exceeding 1500 W, we
recommend to fi t a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this tool
(see technical data). The minimum conductor size is
2
1.5 mm
.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
2
Conductor size (mm
) Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Voltage Amperes
115
230
Voltage drops
Inrush currents cause short-time voltage drops.
Under unfavourable power supply conditions, other
equipment may be affected.
If the system impedance of the power supply is lower than
0.25 Ω, disturbances are unlikely to occur.
Assembly and adjustment
Depth of cut adjustment (fi g. A & B)
•
•
•
.
Bevel adjustment (fi g. C)
The bevel angle can be adjusted between 0° and 45°.
•
•
•
Shoe adjustment for 90° cuts (fi g. D)
•
•
•
•
16
7.5 15 25 30 45 60
Cable rating (Amperes)
0- 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10 10 15 20 20 25
7.1 - 12.0
15 15 20 25 25 -
12.1 - 20.0
20 20 25 -
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10 10 10 10 15 15
7.1 - 12.0
15 15 15 15 20 20
12.1 - 20.0
20 20 20 20 25 -
Prior to assembly and adjustment always
unplug the tool.
Loosen the depth adjustment knob (14).
Move the shoe (6) to obtain the correct depth of
cut.
Tighten the depth adjustment knob (14).
For optimal results, allow the saw blade to
protrude from the workpiece by about 3 mm
(see inset in fi gure B).
Loosen the bevel adjustment knob (11).
Set the bevel angle by tilting the saw shoe (6) until
the mark indicates the desired angle on the scale.
Tighten the bevel adjustment knob (11).
Adjust the saw to 0° bevel.
Retract the blade guard using the lever (8) and place
the saw on the blade side.
Loosen the bevel adjustment knob (11).
Place a square against the blade and shoe to adjust
the 90° setting.
-
Slacken the nut (14) of the stop (15).
-
Adjust the stop (15) as required.
Cable length (m)
6
6
6
10
6
6
15 15
10 15 20 20
-
-
6
6
6
6
6
6
6
6
6
6
10 15
Publicité
Table des Matières
