Publicité
Les langues disponibles
Les langues disponibles
230 V~
50 Hz
FUSE
4
4-Way Antenna Splitter
These instructions are intended for users without
any specific technical knowledge . Please read the
instructions carefully prior to operation and keep
them for later reference . Figures 1 – 3 can be found
on page 2 .
1 Overview
1 BNC jacks, to install the reception antennas on
the front panel;
for insertion of the jacks refer to fig . 1
2 Power LED
3 POWER switch
4 Rear side of the BNC jacks (1); connect the jacks
to the antenna inputs ANT . A and ANT . B (7)
5 Mains jack for connection to a socket (230 V/
50 Hz) via the mains cable provided
The fuse holder is underneath this jack; always
replace a blown fuse by one of the same type!
6 Power supply jacks DC OUTPUT for four re-
ceivers
7 BNC input jacks ANT . A and ANT . B for the an-
tenna signals
8 BNC output jacks ANT . A CASCADE and ANT . B
CASCADE to route the antenna signals to an-
other antenna splitter TXS-875DS
9 BNC output jacks ANT . A 1 ... 4 and ANT . B 1 ... 4
to distribute the antenna signals to the antenna
inputs of four receivers
2 Safety Notes
This unit corresponds to all relevant directives of
the EU and is therefore marked with
WARNING The unit uses dangerous mains
voltage . Never make any modifi-
cation on the unit not described in
these instructions; inexpert han-
dling may result in electric shock .
•
The unit is suitable for indoor use only . Pro-
tect it against dripping water, splash water
and high air humidity . The admissible am-
bient temperature range is 0 – 40 °C .
•
Do not place any vessels filled with liquid, e . g .
drinking glasses, on the unit .
•
Immediately disconnect the mains plug from
the socket
1 . if the unit or the mains cable is visibly dam-
aged,
2 . if a defect might have occurred after the unit
was dropped or suffered a similar accident,
3 . if malfunctions occur .
In any case the unit must be repaired by skilled
personnel .
•
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug .
•
For cleaning only use a dry, soft cloth; never
use water or chemicals .
•
No guarantee claims for the unit and no liability
for any resulting personal damage or material
damage will be accepted if the unit is used for
other purposes than originally intended, if it is
ANT. A
12 V/1A
CASCADE
1
DC
OUTPUT
12 V/1A
5
6
7
8
not correctly connected or operated, or if it is
not repaired in an expert way .
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which is not harmful
to the environment .
3 Applications
The antenna splitter TXS-875DS is designed for
operating up to four multifrequency receivers from
IMG STAGELINE which
– operate in a frequency range between 470 and
960 MHz
– are equipped with removable antennas (BNC
connection)
– are supplied with +12 V/1 A max .
The TXS-875DS makes it easier to set up the audio
transmission system: Only two of the antennas
supplied with each receiver (one pair for each re-
ceiver) are required for connection to the antenna
splitter; all other antennas and the power supply
units of the receivers are not required . The split-
ter will send the antenna signals to the receivers
and supply the receivers with power . Matching
connection cables are supplied .
When more than four receivers are operated,
the cascade outputs (8) can be used to connect
multiple TXS-875DS in series . Each antenna split-
ter will be able to supply four receivers with power .
The antenna splitter can also be used in connec-
tion with the antenna signal amplifiers TXS-875B
(available as a pair) . The antenna splitter will sup-
ply the amplifiers with power .
.
4 Operation
4.1 Preparation and setting up
1) When the antenna signal amplifiers TXS-875B
are used, the 12 V supply voltage for these
amplifiers must be available at the jacks ANT . A
and ANT . B (7) . Prior to operation, please make
sure that the corresponding switch for the sup-
ply voltage in the unit (fig . 2 on page 2) has
been set to the position ON .
WARNING Always disconnect the mains
2) To install the reception antennas on the front
panel of the TXS-875DS, insert the two BNC
jack-to-jack adapters supplied with the unit into
the mounting holes on the left and on the right
and screw them on (refer to fig . 1 on page 2) .
3) Place the antenna splitter on a flat surface
or install it into a rack for units with a width
of 482 mm (19") . For installation into a rack,
1 rack space (= 44 .45 mm) is required .
4.2 Connection and switching on
The connection options can be found in fig . 3
on page 2 .
1) Connect the low voltage jacks DC OUTPUT (6)
to the power supply jacks of the receivers .
ANT. A OUTPUT
2
3
4
4
9
plug before opening the unit;
otherwise, you will risk an
electric shock .
ANT. B OUTPUT
ANT. B
3
2
1
CASCADE
8
7
2) Connect the antenna pair of one of the receiv-
ers to the antenna splitter:
– either to the two jacks (1) on the front panel
of the unit; in this case, connect the rear
side (4) of these jacks to the jacks ANT . A
and ANT . B (7)
– or directly to the two jacks ANT . A and ANT . B
(7) on the rear panel of the unit .
When using the antenna signal amplifiers
TXS-875B, insert the amplifiers between the
antennas and the antenna splitter .
3) Connect the two antenna inputs of each re-
ceiver to an antenna output ANT . A 1 ... 4 and
to the corresponding antenna output ANT . B
1 ... 4 (9) .
4) The antenna signals can be routed to an other
TXS-875DS: Connect the outputs ANT . A
CASCADE and ANT . B CASCADE (8) to the
inputs ANT . A and ANT . B (7) of the following
TXS-875DS . This splitter in turn allows con-
nection of four receivers .
5) Finally, connect the mains cable provided to the
mains jack (5) and connect the mains plug of
the cable to a socket (230 V/ 50 Hz) .
6) To switch the antenna splitter on or off, press
the button POWER (3) . When the unit is
switched on, the power LED (2) will light up .
Notes:
1 . If the antenna splitter provides 4 receivers with
power, the switch-on current of all receivers may
be too high and the power supply unit of the splitter
will not start . In this case, briefly switch off one of
the receivers .
2 . If the TXS-875DS is not used for a longer period
of time, always disconnect the mains plug from
the mains socket; even when the splitter has been
switched off, it will still consume some power while
it is connected to the mains .
5 Specifications
Frequency range: . . . . . . . 470 – 960 MHz
RF amplification: . . . . . . . . 3 dB
DC voltage outputs: . . . . . 12 V, 1 A (4 ×)
Ambient temperature: . . . 0 – 40 °C
Power supply: . . . . . . . . . . 230 V/ 50 Hz
Power consumption: . . . . . 60 VA
Connections for
antenna signals: . . . . . . . . BNC jacks, 50 Ω
Operating voltage (DC) for
antenna signal amplifiers: . 12 V (can be
Dimensions: . . . . . . . . . . . 482 × 45 × 250 mm,
Weight: . . . . . . . . . . . . . . 2 .2 kg
Subject to technical modification .
All rights reserved by MONACOR
& Co. KG. No part of this instruction manual may be repro-
duced in any form or by any means for any commercial use.
12 V/1A
DC
OUTPUT
12 V/1A
6
4
switched off)
1 rack space
®
INTERNATIONAL GmbH
5
Publicité
