Commissioning; Working With The Chain Sharpener; Sharpening The Saw Chain - ATIKA KSG 220 A Notice Originale

The small parts required for mounting are not included in the
scope of delivery. Use the following for this purpose:
Position Description
1. Hexagonal screw M 8 x ....(Length depending
on the thickness of the work table)
2. Washer Ø 8mm
3. Hexagon nut M 8, self-locking

Commissioning

Mains connection
Compare the voltage listed on the device type plate, e.g. 230 V,
with the mains voltage and connect the chain sharpener to the
corresponding and properly grounded socket.
 Alternating current motor:
Use a shockproof plug, mains voltage 230 V with
residual current circuit breaker (30 mA) and 10 A inert
fuses.
 Use connection cable or extension cable respectively with a
cross section of at least 1.5 mm².
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switching on
Press "I" of the ON-OFF switch (12).
Switching off
To turn off the device, press "" of the ON-OFF switch.

Working with the chain sharpener

Before commencing work, ensure the following:
 Workplace tidied?
 Is the chain sharpening device
 complete and properly installed?
 in good and safe condition?
 firmly mounted on the work surface?
 Do you wear the required protective equipment?
 You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Working instructions
The protective cover (20) must cover the grinding
wheel as much as possible.
For this loosen the two screw caps (14) and adjust the
protective cover appropriately.
Never use the chain sharpening device without
protective cover.
Always keep your hands at a safe distance to the
rotating grinding wheel.
 Use the factory-installed grinding wheel only to sharpen
chains used in hobby applications (1/4, 3/8 hobby and 0.325
chains). (An optional grinding wheel 100 x 4.5 x 10 mm,
item no. 363718, is available for professional cutting chains.
 Check the grinding wheel for irregularities, deformation or
cracks before each use.
 Do not use any damaged grinding wheels or such that have
changed their shape.
 Start working only after the grinding wheel has reached its
maximum speed.
 Only chains may be worked that can be put down and
guided securely.
At any rate, follow all instructions in the sections
"Intended use" and "Safety information".

Sharpening the saw chain

All settings must be made while the motor is switched
off.

Make sure before sharpening that the saw chain is free
from oily residues.

The cutting edges of the cutting link must have the same
length after sharpening.
Focus regarding the settings on the shortest cutting link or
the link with the most pronounced damage to obtain
cutting edges consistently having the same length.
Danger of burning! The saw chain becomes hot
during sharpening. Make sure not to touch the ground
locations.
To grind the cutting edge of a cutting link, proceed as follows:
1. Setting the grinding angle: Loosen the locking nut (7) to turn
the rotary plate (1) to approx. 30° and retighten the locking
nut.

The cutting edges of the cutting links are normally
ground at an angle between 30 and 35°.
2. Loosen the mounting screw (3b) and place the cutting
chain in the guide rail (6) between the guide plates (5).
3. Fold the chain stop (4) down and pull the chain toward
the back until the cutting link to be ground rests against the
stop.
4. Pull the grinding head (13) against the cutting link for
exact alignment. Set the distance with the help of the
mounting screw (3a) so that the grinding wheel touches the
cutting link. In addition, adjust the grinding depth with the
setting screw (8).
5. Tighten the mounting screw (3b) chain is fixed in place.
15