TESY GCV50L Manuel D'utilisation page 16

ANODE (FOR WATER HEATERS WITH WATER
EN
TANKS COVERED BY GLASS-CERAMIC OR ENAMEL
COATING)
The magnesium anode provides additional protection
to the water tank's inner surface from corrosion. It is an
element undergoing wear and tear and is subject to
periodic replacement, which is at the expense of the
user. In view of the long-term and accident-free use
of your water heater, the manufacturer recommends
periodic inspections of the magnesium anode's
condition by a qualified technician and replacement
whenever required, and this could be performed during
the appliance's technical preventive maintenance.
For replacements, please contact the authorized service
centres or a qualified technician!
OPERATION.
VII.
Button Function
Button for switching on and off.(Stand by)
Illuminated in white when the appliance is in a
standby mode (the heating element is switched
off).
•
When touched and switched on:
Illuminated in red when the heating
• element is switched on and is heating up;
Illuminated in blue when the set
temperature has been reached and there
is no heating up.
PROG Button for selecting a mode of operation.
By a one-time touching you can choose
among the following modes:
Mode 1 – manual. Indication on the
display. Operation in a mode as an ordinary
thermostat. Constantly maintains the set
temperature.
Mode 2 – P1 – possibility to programme the
time for switching on and off over seven days
Mode 3 – P2 – possibility to programme the
time for switching on and off over seven days
Mode 4 – P3 – possibility to programme the
time for switching on and off over seven days
For detailed description of the programming
method, please see the electronic version of
the instruction on TESY's website
Button for changing values and moving in
<
the menu, if you have chosen any of the three
programme modes.
In manual mode
temperature decreases. When the minimum
possible temperature for setting is reached,
if you continue pressing it, the appliance
will automatically switch to the maximum
possible temperature for setting.
This button is used also for moving in the
menu, if you have chosen any of the three
programme modes. For further information
about the programming method, please see
the electronic version of the instruction on
TESY's website
16
if you press it, the set
> Button for changing values and moving in
the menu, if you have chosen any of the three
programme modes.
In manual mode
temperature increases. When the maximum
possible temperature for setting is reached,
if you continue pressing it, the appliance
will automatically switch to the minimum
possible temperature for setting.
This button is used also for moving in the
menu, if you have chosen any of the three
programme modes. For further information
about the programming method, please see
the electronic version of the instruction on
TESY's website.
BOOST "Boost " function
To enable the BOOST function, press and hold
(for about 3 seconds). The BOOST function
is active in the following modes "Eco Smart",
"Vacation" and "Weekly Programmer "(P1, P2
and P3).
By pressing and holding this button pressed
for 3 seconds you lock all other buttons of
the control panel and no commands can be
entered by them. You can deactivate this
function by pressing the button again for 3
seconds.
Button for selecting "Eco Smart" mode.
ECO
By pressing the ECO/SMART button you
SMART
can chose among three modes: ECO, EC1 or
EC2. In "Eco Smart" mode the electric heater
elaborates its own algorithm for operation so
as to ensure energy saving, and therefore, to
reduce your electricity bill and at the same
time to keep maximum comfort while it is
being used.
Explicit description that ECO mode is with
maximum efficiency, based on which we have
announced the energy efficiency.
OK Multifunctional button for confirmation
of the functions, for selecting days of the
week while setting the weekly programme,
for switching between ON and OFF status
of the time zones while setting the weekly
programme
i
1- In manual mode
By pressing this button the set temperature
will be displayed.
2- In Stand by mode, i.e. when the appliance
is not switched on.
Press and hold the i button. First set the day
of the week using the arrows >, < and confirm
by the OK button. Then set the hour and the
minutes again using the arrows >, < and the
OK button.
3 – In Weekly Programmer mode (P1, P2 and P3)
By this button you can check the time and
the days of the week when the appliance will
operate and will heat the water.
, if you press it, the set
: