Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
E NG LI S H
Please reference the JAY Fusion Cushion Owner's
NOTICE:
Manual for set-up and adjustment of the cushion. The
following instructions pertain to the installation and
adjustment of the ROHO
only.
A. INSTALLATION OF THE INFLATION TUBE(S)
Some configurations of the JAY Fusion Cushion with the ROHO
DRY FLOATATION
insert come with the inflation tube(s) un-
®
installed. If this is the case, you will have received the following
parts:
1. ROHO
®
DRY FLOATATION
2. 1 or 2 lengths of tube with one end terminated by an infla-
tion valve, the other end
open.
A second tube will be included
if the air insert was a dual
chamber insert. A coupling
connector (A) will have already
been installed in the truncated
inflation tubes.
•
Figure 1 shows a Dual chambered ROHO
TION
®
insert ready to have the tube length attached by fol-
lowing the steps below.
To install the inflation tube(s)
1. Install the ROHO
®
DRY
FLOATATION
insert
®
into the JAY Fusion foam
base with inner cover as
outlined in the instruc-
tions below.
2. Measure the length of
inflation tube required
for your specific cushion
size (Figure 2). Do this by threading the tube through the
loops on the inner cover to the front edge. Measure about
1/2" (13mm) from the front edge of the cushion, and run it
the distance (L) until the open end matches up with the tube
valve coming out of the Insert.
3. Cut the length of inflation tube as measured using a sharp
pair of scissors.
4. Insert the coupling connector into the cut length of each infla-
tion tube,
®
DRY FLOATATION
®
Insert
®
insert
A
®
DRY FLOATA-
13mm
13mm
B. INSTALLATION OF THE ROHO
TION
®
INSERT INTO CUSHION
1. With the outer cover removed from the JAY Fusion foam
base, install the ROHO
Well. Ensure that the ROHO
is aligned with the well
and that the inflation
®
tubes are to the rear
of the cushion. (See
Figure 3). Ensure the
Velcro attached to the
ROHO
®
DRY
FLOATATION
is aligned with the
1
matching Velcro
adhered to the inner
cover.
2. With the ROHO
inflation tube(s) need to be secured to the inner cover.
Your ROHO
®
FLOATATION
may have one or two
inflation tubes depend-
ing if it is a single
chamber insert or a
dual chamber insert.
Use the fabric loops on
either side of the inner
2
cover to route the
inflation tube(s). (Figures 4 and 5)
3. Thread the inflation tube through the loops starting at the
rear of the inner cover and inserting the tube through each
loop, working your
way around to the
front of the product.
4. If the ROHO
FLOATATION
is dual chambered, do
the same for the sec-
ond inflation tube on
the opposite side.
5. Re-install the outer cover by sliding it over the base and
inner cover assembly. It is best to hold the inflation valve in
place with your hand as you slide the cover over the assem-
bly.
6. Insert the valve
through the slot in
the outer cover
behind the JAY
Fusion logo. The
valve is intended to
protrude through
the slot and be
secured by the side
band on the JAY
Fusion cover. (Figure 6)
3
INSTALLATION
DRY FLOATA-
®
®
DRY FLOATATION
DRY FLOATATION
®
®
insert
DRY FLOATATION
insert installed, the
®
®
DRY
®
insert
®
DRY
®
insert
®
insert into the
insert
®
3
4
5
6
124610 Rev. A
Publicité
Table des Matières
