Safety Instructions; Before Setting Into Operation; Setting The Unit Into Operation For The First Time; Sources Of Danger - UWE JetSTREAM TREVI Traduction Des Instructions D'utilisation Et D'installation

1

SAFETY INSTRUCTIONS

1.1

Before Setting into Operation

Read instructions!
Before installation and setting into operation, the Safety Instructions and the Operating Instructions must be carefully read and
observed. You must definitely comply with the requirements of the uwe company and of the standards authorities.
1.2

Setting the Unit into Operation for the First Time

Before the unit is set into operation, the local safety regulations and the Safety Instructions must always be complied with.
1.3

Sources of Danger

Attention!
The JETSTREAM system forces up to 720 litres of water per minute into the pool through the nozzle. If all of this enormous force is used for massage, it
can cause injuries to muscles and to connective tissue, as well as internal injuries. Because of the reduced electrical resistance of the human body in
swimming pools and the resulting increased probability of the occurrence of dangerous currents in the body, increased safety requirements are imposed
on the electrical installation.
Attention! Therefore, be sure to keep a following safety instructions.
The jet has a considerable energy. Chokes sure before massaging the jet pressure.
Judge not the full massage jet against the soft tissues of the body.
For pivoting the jet pump switch off.
For large-scale massage radiant intensity throttle to half strength.
Mounting and dismounting For Massage hose, turn off the pump.
Keep to the point massage the nozzle of the hose underwater massage firmly in hand. Run the nozzle of the hose massage at a
distance above the desired locations.
Not open long hair for Inlet strainer (if any) dive.
For requirements regarding the appropriate electrical installation, please see "Information for the Electrician". Parts of the equipment that contain electri-
cally live parts must be inaccessible to persons using the pool. Units and unit parts containing electrical components must be installed or fixed in such a
way that they cannot fall into the water. Units of enclosure class I must be permanently connected to permanently laid cables.
1.4

Proper Operation

All units are intended soleley for operation in covered swimming pools and in open-air swimming pools with a water temperature up to 35°C. The units are
suitable for installing and operating in installations and rooms in areas 1 and 2 as per EN-60335-2-41. The pump is normally installed in the walkway
behind the pool wall, but it must be ensured that the environment is dry and that the motor is protected by a suitably sized floor drain to prevent flooding.
The control panel should be installed either in a dry walkway or in an adjacent room, if possible higher than the water level. Any kind of use other than the
intended use is improper. The manufacturer will not accept liability for any damage or injury resulting from improper operation; the user alone must bear
this risk. Proper operation also includes compliance with the operating, maintenance and repair conditions specified by the manufacturer. Maintenance
work, repair work and suchlike may only be performed by authorised persons.
The units may only be used by persons who are familiar with them and who have been informed about the dangers. The relevant regulations for the
prevention of accidents and the other generally recognised rules relating to safety and to occupational medicine must be complied with. If unauthorised
modifications are made on the units, the manufacturer will not accept liability for any resulting damage or injury.
1.5

Product Liability

The user's attention is expressly drawn to the fact that the unit may only be operated in the proper manner. If it is operated in an improper manner, the user
must bear sole responsibility. In such cases, therefore, the manufacturer cannot accept any liability.
1.6

Procedure in an Emergency

Leave the water immediately, switch off the electrical supply to the unit by operating the main power switch or circuit-breaker,
and secure the unit to prevent it from being switched on again without authorisation.
1.7

Explanation of the danger symbols

Attention!
In these Operating Instructions, this symbol is used to mark all texts relating to safety.
Please pass all safety instructions on to other users.
Function!
In these Operating Instructions, this symbol is used to mark all instructions relating to function.
These instructions must be observed in order to avoid damage to the unit.
Dangerous voltage!
Danger of electric shock! Electricity can cause serious injuries.
11