Safety Checks - GGP ITALY TR 24 Li Manuel D'utilisation

1. remove the line cutting knife (Fig. 11.A)
from the cutting means guard (Fig. 11.B)
unscrewing the screw (Fig. 11.C);
2. rotate the line cutting knife by 180°
3. only for model TR 24 Li B: Position
the line cutting knife in the inner hole;
4. re-assemble the line cutting knife (Fig. 11.A)
on the cutting means guard (Fig. 11.B).
6.1.2 Regulating the front hand grip
1. Remove the knob (Fig. 12.A);
2.
2.a For model TR 24 Li B:
– move the front hand grip in the most
ergonomic position for the operator;
2.b For model TR 24 Li:
– move and/or direct the hand grip in the most
ergonomic position for the operator; it is
possible to direct the hand grip only forwards.
3. Tighten the knob (Fig. 12.A).
6.1.3 Rod length regulation (only
for model TR 24 Li B)
1. Loosen the knob (Fig. 13.A) following the
direction of the arrow - open padlock.
2. pull or push the rod (Fig. 13.B) until
it reaches the desired length;
3. when the adjustment is complete,
tighten the hand grip following the
direction of the arrow - closed padlock.
6.1.4 Rod height regulation (only
for model TR 24 Li)
1. Press the button (Fig. 14.A) and adjust
the rod height (Fig. 14.B) on one of the
four possible positions (Fig. 14.C);
2. make sure the rod is firmly locked.
6.1.5 Aligning the cutting device
The cutting means orientation allows to switch
from grass trimmer mode to grass edge trimmer
mode, and vice versa, while working (Par. 3.1).
How to work in grass trimmer mode:
1.
1.a For model TR 24 Li:
– Press the button (Fig. 15.A);
– Rotate the cutting means (Fig. 15.B) by 90°,
making sure it stays locked in the position.
1.b For model TR 24 Li B:
– Pull the upper sleeve backwards (Fig. 16.A);
– Rotate the lower part of the rod
by 180° (Fig. 16.B), making sure
it stays locked in the position.
Perform this operation when
the machine is turned off and
the cutting means is still.
6.1.6 Cutting limit indicator adjustment
(only for model TR 24 Li B)
– Rotate forwards the cutting limit
indicator (Fig. 17.A) when working
near trees, kerbs or fences, to avoid
the impact with the cutting means.
6.1.7 Checking the battery
Before each use:
– check the battery charge status according
to the instructions in the battery booklet.

6.2 SAFETY CHECKS

Run the following safety checks and
check that the results correspond to
those outlined on the tables.
Always carry out the
safety checks before use.
6.2.1 General check
Object
Hand grips (Fig. 1.E)
Cutting means
guard (Fig. 1.D)
Screws on the machine
Cutting means (Fig. 1.C)
Battery (Fig. 1.G)
Cooling air ducts (par. 7.3) Not clogged
Machine
Throttle control lever
(Fig. 10.A), throttle
safety lever (Fig. 10.B)
Test driving
EN - 10
Result
Clean, dry and fixed
firmly to the machine.
Correctly and securely fit
to the machine, not worn/
deteriorated or damaged.
Correctly tightened
(not loose)
Clean, not damaged
or worn.
No damage to the casing,
no liquid leakage
No signs of damage
or wear
The levers must move
freely and not be forced.
No abnormal vibrations.
No abnormal sound