Bosch PCM 8 SD Notice Originale page 25

Safety Warnings for Mitre Saws
Mitre saws are intended to cut wood or wood-like
u
products, they cannot be used with abrasive cut-off
wheels for cutting ferrous material such as bars, rods,
studs, etc. Abrasive dust causes moving parts such as
the lower guard to jam. Sparks from abrasive cutting will
burn the lower guard, the kerf insert and other plastic
parts.
Use clamps to support the workpiece whenever pos-
u
sible. If supporting the workpiece by hand, you must
always keep your hand at least 100 mm from either
side of the saw blade. Do not use this saw to cut pieces
that are too small to be securely clamped or held by
hand. If your hand is placed too close to the saw blade,
there is an increased risk of injury from blade contact.
The workpiece must be stationary and clamped or
u
held against both the fence and the table. Do not feed
the workpiece into the blade or cut "freehand" in any
way. Unrestrained or moving workpieces could be thrown
at high speeds, causing injury.
Push the saw through the workpiece. Do not pull the
u
saw through the workpiece. To make a cut, raise the
saw head and pull it out over the workpiece without
cutting, start the motor, press the saw head down and
push the saw through the workpiece. Cutting on the
pull stroke is likely to cause the saw blade to climb on top
of the workpiece and violently throw the blade assembly
towards the operator.
Never cross your hand over the intended line of cut-
u
ting either in front or behind the saw blade. Supporting
the workpiece "cross handed" i.e. holding the workpiece
to the right of the saw blade with your left hand or vice
versa is very dangerous.
Do not reach behind the fence with either hand closer
u
than 100 mm from either side of the saw blade, to re-
move wood scraps, or for any other reason while the
blade is spinning. The proximity of the spinning saw
blade to your hand may not be obvious and you may be
seriously injured.
Inspect your workpiece before cutting. If the work-
u
piece is bowed or warped, clamp it with the outside
bowed face toward the fence. Always make certain
that there is no gap between the workpiece, fence and
table along the line of the cut. Bent or warped work-
pieces can twist or shift and may cause binding on the
spinning saw blade while cutting. There should be no nails
or foreign objects in the workpiece.
Do not use the saw until the table is clear of all tools,
u
wood scraps, etc., except for the workpiece. Small
debris or loose pieces of wood or other objects that con-
tact the revolving blade can be thrown with high speed.
Cut only one workpiece at a time. Stacked multiple
u
workpieces cannot be adequately clamped or braced and
may bind on the blade or shift during cutting.
Bosch Power Tools
Ensure the mitre saw is mounted or placed on a level,
u
firm work surface before use. A level and firm work sur-
face reduces the risk of the mitre saw becoming unstable.
Plan your work. Every time you change the bevel or
u
mitre angle setting, make sure the adjustable fence is
set correctly to support the workpiece and will not in-
terfere with the blade or the guarding system. Without
turning the tool "ON" and with no workpiece on the table,
move the saw blade through a complete simulated cut to
assure there will be no interference or danger of cutting
the fence.
Provide adequate support such as table extensions,
u
saw horses, etc. for a workpiece that is wider or
longer than the table top. Workpieces longer or wider
than the mitre saw table can tip if not securely supported.
If the cut-off piece or workpiece tips, it can lift the lower
guard or be thrown by the spinning blade.
Do not use another person as a substitute for a table
u
extension or as additional support. Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling you
and the helper into the spinning blade.
The cut-off piece must not be jammed or pressed by
u
any means against the spinning saw blade. If confined,
i.e. using length stops, the cut-off piece could get wedged
against the blade and thrown violently.
Always use a clamp or a fixture designed to properly
u
support round material such as rods or tubing. Rods
have a tendency to roll while being cut, causing the blade
to "bite" and pull the work with your hand into the blade.
Let the blade reach full speed before contacting the
u
workpiece. This will reduce the risk of the workpiece be-
ing thrown.
If the workpiece or blade becomes jammed, turn the
u
mitre saw off. Wait for all moving parts to stop and
disconnect the plug from the power source and/or re-
move the battery pack. Then work to free the jammed
material. Continued sawing with a jammed workpiece
could cause loss of control or damage to the mitre saw.
After finishing the cut, release the switch, hold the
u
saw head down and wait for the blade to stop before
removing the cut-off piece. Reaching with your hand
near the coasting blade is dangerous.
Hold the handle firmly when making an incomplete cut
u
or when releasing the switch before the saw head is
completely in the down position. The braking action of
the saw may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
Keep your work area clean. Material mixtures are partic-
u
ularly hazardous. Light metal dust may catch fire or ex-
plode.
Do not use dull, cracked, bent or damaged saw blades.
u
Unsharpened or improperly set saw blades produce
narrow kerf causing excessive friction, blade binding
and kickback.
English | 25
1 609 92A 4M8 | (04.12.2018)