Clarion DXZ788RUSB Mode D'emploi page 26

01_DXZ788RUSB_EN.book 26 ページ ２００７年１１月２７日 火曜日 午後６時３４分
Radio Data System Operations
REG (Regional programme)
function
When the REG function is ON, the optimum
regional station can be received. When this
function is OFF, if the regional station area
switches as you drive, a regional station for that
region is received.
∗ The factory default setting is "OFF".
Notes:
• This function is disabled when a national station
such as BBC R2 is being received.
• The REG function ON/OFF setting is valid when
the AF function is ON.
1. Press the [OPTION] button.
2. Push the [SEEK PANEL] leftward or
rightward to select "REG".
3. Push the [P.CH] button upward or downward
to select " or "OFF".
"ON
• ON:
"REG" in the display lights and REG function
turns on.
• OFF:
"REG" in the display goes off and REG
function turns off.
4. Press the [OPTION] button to return to the
previous mode.
Manually tuning a regional station
in the same network
1. This function is valid when the AF function is
ON and the REG function is OFF.
Note:
• This function can be used when a regional
broadcast of the same network is received.
2. Push the [P.CH] button upward or downward
to call out the regional station.
3. If the reception condition of the called out
station is bad, push the [P.CH] button
upward or downward to select the same
preset memory station. The unit receives a
local station on the same network.
TA (Traffic Announcement)
In the TA standby mode, when a traffic
announcement broadcast starts, the traffic
announcement broadcast is received as top
priority regardless of the function mode so you
can listen to it. Traffic programme (TP)
automatic tuning is also possible.
26
DXZ788RUSB
∗ This function can only be used when "TP" is lit in
the display. When "TP" is lit, this means that the
"Radio Data System" broadcast station being
received has traffic announcement programmes.
Setting the TA standby mode
If you press the [TA] button when only
in the display, " and "TA" light in the display
"TP
and the unit is set into the TA standby mode
until a traffic announcement is broadcast. When
a traffic announcement broadcast starts, "TRA
INFO" appears in the display. If you press the
[TA] button while a traffic announcement
broadcast is being received, the traffic
announcement broadcast reception is cancelled
and the unit goes into the TA standby mode.
Cancelling the TA standby mode
As "TP " and "TA" lit in the display, press the [TA]
button. The "TA" in the display goes off and the
TA standby mode is cancelled.
∗ If "TP" is not lit, pressing the [TA] button searches
for a TP station.
Searching for a TP station
When " is not lit, if you press the [TA] button,
"TP
"TA" in the display lights and the unit
automatically receives a TP station.
Note:
• If a TP station is not received, the unit continues
the search operation. Pressing [TA] button again
goes off "TA " in the display and stops TP station
searching.
Auto store function for TP stations
You can automatically store up to 6 TP stations
into preset memory. If the number of TP can be
received less than 6, broadcast stations already
stored in memory and left without being
overwritten.
As "TA" lit in the display:
1. Press the [OPTION] button.
2. Push the [SEEK PANEL] leftward or
rightward to select "AUTO STORE".
3. Press and hold the [
seconds or longer.
The TP stations with the good reception
sensitivity are stored into preset memory.
∗ Even if you select FM1 or FM2, a TP station is
stored into memory for FM3.
"TP " is lit
] button for 2