Safety Instructions For All Operations - Dremel MICRO 8050-35 Traduction De La Notice Originale

c. Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g. Use the power tool, accessories and
tool bits etc., in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
a. Recharge only with the charger speciied
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of ire when used with another
battery pack.
b. Use power tools only with speciically
designated battery packs. Use of any other
battery packs may create a risk of injury and
ire.
c. When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws, or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a ire.
d. Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, lush with
water. If liquid does make contact with
eyes, then seek medical help. Liquid ejected
from the battery may cause irritation or burns.
a. Have your power tool serviced by a
qualiied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
BATTERY TOOL USE AND CARE
SERVICE
SAFETY INSTRUCTIONS FOR
ALL OPERATIONS
SAFETY WARNINGS COMMON FOR
GRINDING, SANDING, WIRE BRUSHING,
POLISHING OR ABRASIVE CUTTING-OFF
OPERATIONS
a. This power tool is intended to function
as a grinder, sander, wire brush, polisher,
carving or cut-off tool. Read all safety
warnings, instructions, illustrations and
speciications provided with this power
tool. Failure to follow all instructions listed
below may result in electric shock, ire and/or
serious injury.
b. Do not use accessories which are not
speciically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
c. The rated speed of the grinding
accessories must be at least equal to the
maximum speed marked on the power
tool. Grinding accessories running faster than
their rated speed can break and ly apart.
d. The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly sized accessories cannot be
adequately controlled.
e. The arbour size of wheels, sanding drums,
or any other accessory must properly it
the spindle or collet of the power tool.
Accessories that do not match the mounting
hardware of the power tool will become
unbalanced, vibrate excessively and may
cause loss of control.
f. Mandrel mounted wheels, sanding drums,
cutters or other accessories must be
fully inserted into the collet or chuck.
If the mandrel is insuficiently held and/or
the overhang of the wheel is too long, the
mounted wheel may become loose and be
ejected at high velocity.
g. Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
sanding drum for cracks, tear or excess
wear, wire brush for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting
and installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
h. Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping lying debris
generated by various operations. The dust
mask or respirator must be capable of
iltrating particles generated by your operation.
11