Table des Matières
Publicité
Carefully read and understand this manual and any label
attached to the tool before use. Keep these instructions with
the product for future reference. Ensure all persons who use
and service this product are acquainted with this manual.
Electrical Safety Information
The wires in this product are colored:
Blue
Brown
Green & Yellow
FUSE
GREEN/YELLOW
OR GREEN
BLUE
BROWN BLUE
(Neutral)
(Live)
Double Insulated
As the colours may not correspond with the coloured
markings identifying the terminals in your plug, proceed as
follows.
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured to the
terminal which is coloured brown must be connected to the
terminal which is marked L or coloured red.
This appliance must be protected by a suitable fuse.
To prevent fire or shock hazard, do not expose this product
to rain/water or moisture. There are no use serviceable parts
inside except those referred to in this manual. Always refer
servicing to qualified service personnel. Never remove any
part of the casing unless qualified to do so; this unit contains
dangerous voltages.
Use of a residual current device (RCD) will reduce the risk of
electric shock.
NEVERCONNECT THE BROWN OR BLUE WIRE TO THE
EARTH PIN OF THE 13 AMP PLUG. IF IN DOUBT
QUALIFIED ELECTRICIAN
General Safety Instructions
Even when used as prescribed it is not possible to eliminate all
residual risk factors. Use with caution.
Keep guards in position
Always keep guards in position, in good working order,
correctly adjusted and aligned. Never attempt to use a
power tool without any guard supplied with it.
Remove adjusting keys
Always check to see that keys and adjusting wrenches are
removed from power tool before turning on.
Clean work area
Accidents occur where benches and work areas are
cluttered or dirty, floors must be kept clear, avoid working
where the floor is slippery.
Dangerous environment
Do not use power tools in damp or wet conditions, or expose
them to rain. Provide adequate surrounding work space and
keep area well lit. Do not use power tools where is a risk of
explosion or fire from combustible material, flammable
liquids, flammable gases or dust of an explosive nature.
When using power tools avoid contact with any earthed
items such as pipes, radiators, cookers, refrigerators, metal
baths and taps.
Children & pets
Children and pets should always be kept at a safe distance
from your workshop. Lock tools away where children can't
get access to them. Remove batteries from cordless tools.
Use the correct power tool
Don't force, or attempt to use a power tool for a purpose it
was not designed for. Do not use a small tool to do the job
of a heavy duty tool.
Wear correct clothing and footwear.
Don't wear loose clothing, neckties or jewellery or other
items which may get caught in moving parts. Wear mom-slip
footwear, cover or tie back long hair. Use safety footwear if
necessary.
Introduction
Neutral (N)
Live (L)
Earth (E)
FUSE
BROWN
(Neutral)
(Live)
Earthed
CONSULT A
Protect your head
Wear safety goggles at all times, every day
glassed are not sufficient for eye protection,
as lenses are not impact resistant and could
shatter. Use an approved face or dust mask
when operation creates dust. Ensure dust
extraction equipment is function and
correctly used. Hearing protection should be
used if the sound intensity level for the
operator could exceed 85dB(A). Use a hard
hat where there is a risk of falling objects or
striking your head on low level obstructions.
Protect yourself form vibration.
Hand held power tools may produce
vibration, Vibration can cause disease.
Gloves to keep the operator warm and dry
and therefore maintain good blood
circulation in the fingers may help. This tool
has not been designed for extended or
industrial operation.
Secure work
Always secure work. Where practical use a
clamp or vice, it will allow you to use both
hands to operate your power tool.
Keep your balance
Don't over reach, keep proper footing at all
times to ensure correct balance.
Maintain your power tool
Keep your power tool in good working order,
keep tools sharp and clean for best and
safest performance. Ensure ventilation holes
are kept clean and unrestricted at all times.
Always disconnect
Before changing tools, always ensure they
are disconnected from the power source.
Accessories
The use of any attachment or accessory
other than those mentioned in this manual
could result in damage or injury. The use of
improper accessories could be dangerous.
Switch off before connecting.
Ensure the power tool is switched off before
connecting to the power source. If the power
tool stops unexpectedly turn the power
switch to off.
Do not abuse the power cord.
Be sure your cable/extension cable is
properly wired and in good condition. Always
replace a damaged cable/extension cable or
have it repaired by a qualified person before
using it. Never yank or pull the cable to
disconnect it from the power socket. Never
carry your power tool by it's cable. Keep the
cable away from damp, heat, oil, solvents,
and sharp edges.
Check for damaged or missing parts.
Before each use check if any part of the
power tool is damaged or missing, check
carefully that it will operate properly and
perform its intended function. Check
alignment of moving parts for binding. Any
guard or other part that is damaged should
be correctly repaired or replaced. Do not use
if the power switch does not turn the power
in and off. Check any other condition that
may affect the safety of the power tool. DO
NOT USE IF DEFECTIVE.
Direction of feed
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter
only.
Don't leave the tool running unattended
Always wait unit your power tool has come to s
complete stop before leaving it and then
disconnect from power source.
Publicité
Table des Matières
