Briteq BT-30FC WASH Mode D'emploi page 5

ENGLISH
 Use DOWN and UP buttons to change the DMX512 address.
 Once the correct address shows on the display, press the ENTER
button to save it.
To go back to the main menu without any change press the MENU button
shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Channel Mode
 Press the MENU button until
is shown on the display.
 Press the ENTER button so the display starts blinking.
 Use DOWN and UP button to select the
Channel) or 1channel mode.
 To use the master / slave mode with dmx control, select the
mode or the mode.
 Once the mode is selected, press the ENTER button to confirm.
To go back to the main menu without any change press the MENU button
shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Slave Mode
Used to make the slave unit work in opposite to the master or to
work in complete sync.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
show) mode.
 Once the mode is selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button
shortly.
If you want to go back to normal running mode: press the MENU button
for about 2 seconds.
Show Mode
Used to choose the Show mode when used in standalone or
master/slave mode.
 Press the MENU button until "ShMd" is showing on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select one of the available shows:
 Show 1 (Sh 1): Fixture is placed on the floor. Tilt movement
angle 210°.
 Show 2 (Sh 2): Fixture is fixed under ceiling. Tilt movement angle
90°.
 Show 3 (Sh 3): Fixture is placed on a podium, in front of the
audience. The spot is always projecting to the audience's
direction; i.e. in front of the stage. Pan movement angle (left to
right to left): 160°. Tilt movement angle: 90° (60° above horizon;
30° below horizon.)
 Show 4 (Sh 4): Fixture is fixed under ceiling. The spot is mainly
projecting in front of the stage. Pan movement angle (left to right to
left):160°. Tilt movement angle: 90° (vertically, front 75°; back 15°)
 Once the right mode shows on the display, press the ENTER button to
save it.
BRITEQ
®
OPERATION MANUAL
(16 Channel), (9
(2 light
5/38 BT-30FC
ENGLISH
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Sound Mode
The unit works to rhythm of the beat when used in standalone or master/slave mode
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
or
 Once the mode has been selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(yes blackout) or
 Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select (normal) or
 Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(normal) or
 Once the mode has been selected, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
BRITEQ
®
OPERATION MANUAL
mode.
(no blackout) mode.
.
(display off when not used).
(pan inversion) mode.
(tilt inversion) mode.
6/38 BT-30FC