Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
FUTURA
•
Close the loading door and block with lever (B) in vertical position.
•
Close lateral feeding door (A).
•
In case of a BRIQUETTES UNLOADING alarm, press the P1 button for more than 3 secondsto reset the alarm.
Press the P1 button again for more than 3 seconds to switch to AUTOMATIC mode.
•
WARNING: The display goes off when the lateral door is opened. After the lateral door is closed the display will resume operation.
12. LIGHTING
WARNING: After the first ignition you can smell bad odours (owing to the drying of the glue used in the garnitures or of the paint) which
disappear after a brief using of the appliance. It must be ensured, in any case, a good ventilation of the environment. Upon the
first ignition we suggest loading a reduced quantity of fuel and slightly increasing the calorific value of the equipment
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the following information:
•
the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iron, steel,
refractory material and majolica;
•
the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures within the
range of 300°C - 500°C are detected;
•
during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycles of intense use
or of absolute standstill when season changes;
•
the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paints to
complete the various elastic stresses;
•
in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet paint.
This paint, although during the manufacture it is backed at 250 °C for some hours, must exceed many times and for a given period of
time the temperature of 350 °C before becoming completely embedded in the metallic surfaces.
Therefore, it is extremely relevant to take these easy steps during the lighting:
1. Make sure that a strong air change is assured in the room where the appliance is installed.
2. During the first starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions manual)
and keep the product continuously ON for at least 6-10 hours with the registers less open than the value indicated in the instructions
manual.
3. Repeat this operation for at least 4-5 or more times, according to your possibilities.
4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum load)
and, if possible, keep the lighting periods long avoiding, at least in this initial phase, short ON/OFF cycles.
5. During the first starts, no object should be leaned on the appliance and in detail on enameled surfaces. Enameled surfaces
must not be touched during heating.
6. Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with excessive
loads.
IMPORTANT: The burn pot must be cleaned on necessity, and in any case on every ignition (see chapter BURN POT CLEANING).
To light the fire, it is suggested to use small wood pieces together with paper or other traded lighting means. It is FORBIDDEN to use any
liquid substance as for ex. alcohol, gasoline, oil and similar.
Never overload the appliance (see the technical table - max quantity of fuel that can be loaded / hourly consumption). Too much fuel and
too much air for combustion can cause overheating and therefore damage the appliance. The warranty does not cover the damages
due to overheating of the equipment. IMPORTANT: Never switch on the device when there are combustible gases in the room.
The ignition must ALWAYS occur in MANUAL MODE (even in the presence of electric voltage, see the CONTROL BOARD - USER
MENU chapter):
•
The primary air register must be completely open and therefore completely extracted
Using the fire iron lift the cast iron COMB
•
appropriate protective clothing or accessory tools (heat-resistant gloves, control devices, etc.).
•
Block the COMB in vertical position with the lever
•
When wood starts to burn, other fuel can be fed, the primary air register is closed (completely inserted), and combustion is controlled
by secondary air
(Picture 6 at page 65
unattended during this phase.
IMPORTANT: FUEL MUST NEVER BE FED ABOVE THE COMB ! Feeding the fuel above the comb will cause the glass door to
break. Therefore, the replacement of the glass is not covered by
Predisposition for AUTOMATIC operation mode:
•
Ignition must ALWAYS occur in MANUAL mode.
•
Add a pressed wood briquette on the wooden slats just ignited.
•
Using the fire iron, release the COMB by pulling it slightly. Move the lever
the COMB above the briquettes
•
When wood starts to burn, proceed as described in the AUTOMATIC OPERATION chapter.
IMPORTANT: FUEL MUST NEVER BE FED ABOVE THE COMB ! Feeding the fuel above the comb will cause the glass door to
break. Therefore, the replacement of the glass is not covered by warranty
8291003 - IT - EN - DE - FR
(Picture 8 at page 65
(Picture 8 at page 65
2A) according to the directions given in the TECHNICAL DATA chapter. Never leave the stove
(Picture 9 at page
65.A).
(Picture 6 at page 65
A). Beware of hot parts. Avoid contact with these items without
B).
warranty.(Picture 10 at page
(Picture 9 at page
65.B) in the release position and accompany
(Picture 10 at page
1A).
66).
66).
27
Publicité
Table des Matières
