Transportation And Handling - Parker Hiross Hypersep SFH013-550 Manuel D'utilisation

Carbon steel centrifugal water separators
SFH013-209: Simple pressure vessel
C
onforms to 2009/105/EC directive;
SFH280-550 / SFH019-097P / SFV029-209 :
C 97/23/EC directive.
onforms to
Please refer to the declaration of conformity document included with
your water separator.
1. Safety instructions
Important:
Keep this manual with the water separator throughout its entire
service life.
Carefully read this manual before carrying out any installation and
operation of the water separator.
Y
Do not exceed the design limits given on the data plate.
!
All compressed air/nitrogen circuits should include appropri-
ate safety devices according to government and industry stand-
ards. Th e end user is responsible for installing safety devices on
the compressed air/nitrogen circuit.
!
Before starting any maintenance operations, make sure that
the compressed air/nitrogen circuit is not under pressure.
Only use the water separator for separating water from com-
pressed air/ nitrogen.
Th e user, through their own analysis and testing, is solely respon-
sible for:
• making the fi nal selection of the appropriate water separator;
• assuring that all user's performance, endurance, maintenance,
safety and warning requirements are met and that the applica-
tion presents no health or safety hazards;
• complying with all existing warning labels and/or providing
all appropriate health and safety warnings on the equipment on
which the water separator is used;
• assuring compliance with all applicable government and
industry standards and regulations; and
• assuring compliance with this manual.
Tampering, modifi cation or replacement of any parts of the water
separator by unauthorised personnel and/or improper use exoner-
ates the manufacturer from all responsibility and invalidates the
warranty.
Th e manufacturer declines any present or future liability for dam-
age to persons, objects and the water separator, due to negligence
of the operators, non-compliance with all the instructions given in
this manual, and non- application of current government and in-
dustry standards and/or regulations regarding safety of the system
in which the water separator is used.
Th e manufacturer declines any liability for damage due to altera-
tions and/or changes to the packaging, decayed or modifi ed pack-
aging or improper handling or installation.
It is the responsibility of the user to ensure that a proper conden-
sate drain is selected for use with the water separator and that the
condensate drain is properly maintained to ensure consistent and
complete drainage from the water separator under all conditions.
Th e manufacture declines any liability for damage caused by or
resulting from improper selection, use or maintenance of conden-
sate drains.
English
When requesting technical assistance always quote the model and
serial number on the data plate mounted externally on the water
separator.

2. Transportation and handling

• Do not store or transport the water separator in an unen-
closed environment.
• Protect the water separator from impact to prevent damage.
• In the event of damage during transportation, handling or
installation do not operate the water separator and replace it
immediately.
Inspection
As soon as you receive the water separator check its condition; if
you notice any damage inform the carrier immediately, do not
install or operate the water separator and replace it immedi-
ately.
3. Installation
Th e water separator typically is installed on the compressed air/ni-
trogen outlet of aft ercoolers, or any other point where condensate
needs to be separated from compressed air/nitrogen.
• See Fig.1 (A,B,C) and Tables 1 / 2 (A,B,C) for water separator
dimensions and fl ange sizing.
• Do not install the water separator in an unenclosed environ-
ment. Install in a ventilated area and away from heat sources
and fl ammable materials which ensure an ambient temperature.
• Support the water separator on suitable mountings to avoid
stressing the inlet and outlet piping.
• Install one or more safety valves as necessary on the com-
pressed air/nitrogen circuit to ensure that maximum pres-
sure of the water separator, as shown on the data plate and
in Table 3, is never exceeded. Th e user should ensure that
installation of safety valves is in compliance with all applica-
ble government and industry standards and regulations.
• If the compressed air/nitrogen circuit is subject to vibra-
tions or pulsations, use appropriate vibration and/or pulsation
dampers to connect the water separator to the compressed air/
nitrogen circuit.
• Ensure that the compressed air/nitrogen does not contain
corrosive gases. Take particular care in or around environments
with high levels of Sulpur, Ammonia, Chlorine and marine
applications. Please be aware that stainless steel models are
available on request in case of corrosive agents being present.
For further advice or assistance consult the manufacturer.
• Care should be taken to prevent accidental contact and burns
when subject to temperatures exceeding 40°C.
• Install the water separator such that the compressed air/nitro-
gen fl ows in the direction indicated by the labels on the water
separator.
• Use appropriate industry standard counter fl anges and gaskets
to connect piping to the water separator. See Table 2 (A,B,C)
for fl ange sizing.
• Install an appropriate condensate drain. Note: carbon steel
materials are subject to rusting. Ensure that the condensate
drain is capable of removing rust particles from the water sepa-
rator with the condensate.
• Make sure that condensate drains can be visually checked
for correct condensate fl ow and are properly maintained and
SFH-P / SFV 1