Care And Storage - Armytek WIZARD C1 PRO Manuel De L'utilisateur

In ON state:
1 click: To turn off the flashlight.
Press and hold: To start cycling through the modes of relevant Section.
The same in OFF & ON states:
2 clicks: To turn on Main mode [Section 2]. Another double click will
switch between chosen modes in [Section 1] and [Section 2].
3 clicks: To turn on Turbo mode [Section 3].
4 clicks: To turn on Strobe mode [Section 4].
Automemorizing. After switching off the last used mode is memorized
for quick access at next switching on.
Safe high brightness modes. Turbo modes give maximum brightness
until the temperature of the flashlight and discharge current of the
battery don't exceed critical values.
Digital Light Stabilization & Safe Soft-Start System allows to in-
crease runtime, get longer lifetime of rechargeable battery and protect
it from overdischarge or overheating.
Active temperature control. When the temperature of the flashlight
becomes close to +58 °С, brightness decreases to safe value, allowing
the flashlight to avoid overheating for a long period of time. In condi-
tions of good air-cooling the flashlight delivers light without stepping
down.
Warning indication shows the battery level and the temperature
inside the flashlight.
Low battery level. When battery level is approximately <25%, the color
LED will show the warning level by flashing orange once in 2 seconds.
With further voltage reduction brightness will start to decrease in steps
for safety of the battery and user. If brightness of the mode (except
Firefly modes and Main1) is approximately <25% from nominal value,
the main LED will flash 2 times. Critical battery level approximately
<10% is indicated by flashing red once a second.
High temperature. When the temperature increases to the warning
level, the color LED flashes orange 3 times once in 2 seconds. At critical
level it flashes red 3 times once in 1 second. Brightness starts to reduce
to safe level.
Lock-out function. Unscrew the tailcap to 1/4 for protection from
accidental switching on. State Indication will be turned off.
Multicolor State Indication. Short flashes every 4 seconds show the
battery level even in OFF state (until battery level becomes lower than
the critical one). The indication also helps to find the flashlight in the
dark.
Switching Multicolor State Indication ON/OFF. The indication is
switched off by default in Firefly modes (disabled after 10 seconds of
operation) and in OFF state. To turn it on/off, unscrew the tailcap to 1/4,
press the button and keeping the button pressed tighten and unscrew
the tailcap again. The settings will be memorized even when battery
is changed. Ultra-low current consumption allows color indication to
work for maximum period of time.
4 ENG USER MANUAL WIZARD C1 PRO
Warnings
For effective operation of the flashlight, we recommend branded 18350
Li-Ion batteries or 16340 Li-Ion batteries without PCB (unprotected) or
with PCB which guarantees 3A discharge current.
The flashlight can get hot in Turbo modes, Strobe2 and Strobe3 quickly
and discharge the battery with high current. Don't leave it without your
attention as very bright light might heat objects and cause fire.
For storage or transportation of the flashlight in a pocket or a bag it is
necessary to activate the lock-out function to ensure protection from
accidental switching on.
It is forbidden to charge the battery inside the flashlight when the
ambient temperature is below 0 °C.
1. Always follow the instructions from this manual and recommenda-
tions on battery usage.
2. Apply only the recommended power sources.
3. Do not reverse battery polarity.
4. Do not modify or recast the flashlight and its components as it will
deprive you of the warranty.
5. Do not allow water or any other liquid to leak into the flashlight.
6. Do not aim a switched-on flashlight at people's or animals' eyes – it
can cause temporary blindness.
7. Do not allow children to use the flashlight without your assistance.
The producer will not be liable for any harm done to the user if it
was caused by improper use of the product.

Care and Storage

It is recommended to clean the threads and O-rings off dirt and old
grease once or twice per year. Remember that reliable protection from
water and dust cannot be provided by worn out sealing. The fouling
as well as lack of lubricant cause fast wear-out of threads and sealing
rings.
To clean the threads do the following:
1. Unscrew the tailcap and remove the sealing ring carefully with a
toothpick (do not use sharp metal things as they can damage the
ring).
REV_00-0001