Festool TS 75 EBQ Notice D'utilisation D'origine/Liste De Pièces De Rechange page 18

cutting depth and push it forward in the cutting
direction. The markings [6-2] display the absolute
front and the absolute rear cutting points of the
saw blade (dia. 210 mm) at maximum cutting
depth and using the guide rail.
5.4 Sawing aluminium
When sawing aluminium, the following
measures must be taken for safety rea-
sons:
- Preconnect a residual current circuitbreaker.
- Connect the machine to a suitable dust extractor.
- Clean the machine regularly of dust deposits in
the motor housing and in the protective cover.
Wear protective goggles.
- Aluminium must only be sawed with the special
saw blades from Festool designed for this pur-
pose.
When sawing panels, they must be lubricated with
petroleum, thin-walled profi les (up to 3 mm) can
be sawed without lubrication.
6 Accessories
The order numbers of the accessories listed below
can be found in the Festool catalogue or on the
Internet under "www.festool.com".
6.1 Parallel stop, table widener
A parallel stop can be used for section widths up
to 180 mm. The parallel stop can also be used as
a table widener.
6.2 Guide system
The guide rails, which are available in different
lengths, allow for precise, clean cuts and simul-
taneously protect the workpiece surface against
damage. In conjunction with the extensive range
of accessories, exact angled cuts, mitre cuts and
fi tting work can be completed with the guide sys-
tem. The option of securing using G-clamps [6-4]
ensures a fi rm hold and safe working. The guide
clearance of the saw table on the guide rails can
be set with the two setting jaws [1-3].
The guide rails are equipped with a splinterguard
[1-4], which has to be cut to size before the fi rst
use:
- Set the speed of the machine to level 6,
- Place the machine on the rear end of the guide
rail,
- Switch the machine on, press it down to the set
cutting depth and cut the splinterguard along
the full length without interruption.
The edge of the splinterguard now corresponds
exactly to the cutting edge.
6.3 Multifunction table
The mutifunction table MFT/3 makes clamping
the workpiece easy and allows you to saw large
and small workpieces safely and precisely using
the guide system. Its many fi elds of application
make economical and ergonomically convenient
work possible.
6.4 Saw blades, other accessories
In order to be able to saw different materials
quickly and cleanly, Festool offers saw blades that
are specially designed for your machine.
The order numbers for these and for other acces-
sories that allow you to use your Festool portable
circular saw effectively and in many ways, can be
found in the Festool catalogue or on the Internet
under "www.festool.com".
7 Maintenance and care
Always remove the plug from the mains
supply socket before carrying out any
work on the machine!
Always keep the machine and the ventilation slots
clean. Any maintenance or repair work requiring
the motor housing to be opened may only be car-
ried out by an authorised service workshop. The
tool is fi tted with special motor brushes with an
automatic cut-out. When the brushes become
worn the power supply is shut off automatically
and the tool comes to a standstill.
8 Disposal
Do not throw the power tool in your household
waste! Dispose of machines, accessories and
packaging at an environmentally-responsible
recycling centre. Observe the valid national regu-
lations.
EU only: European Directive 2002/96/EC stipulate
that used electric power tools must be collected
separately and disposed of at an environmentally
responsible recycling centre.
9 Warranty
For our tools, we give warranty for material and
production defects in accordance with the locally
applicable legal provisions, but in any case for at
least 12 months. Within the EU member states,
the warranty period is 24 months (verifi cation
through invoice or delivery note). Damage caused
18