IMPORTANT SAFETY INSTRUCTIONS
EN
WARNING – To guard against injury, basic safety precautions should be observed,
including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1.
and all the important notices on the appliance before using. Failure to do so may
result in loss of fish life and/or damage to this appliance.
2. DANGER – To avoid possible electric shock, special care should be taken since
water is employed in the use of aquarium equipment. For each of the following
situations, do not attempt repairs yourself; return the appliance to an authorized
service facility for service or discard the appliance.
A. If the appliance shows any sign of abnormal water leakage, immediately unplug it
from the power source.
B. Carefully examine the appliance after installation. It should not be plugged in if
there is water on parts not intended to be wet. If the appliance or any part of it
falls into the water DO NOT reach for it. First unplug the unit before retrieving.
C. Do not operate any appliance if it has a damaged cord or plug, or if it is
malfunctioning or it is dropped or damaged in any manner. The power cord of this
appliance cannot be replaced; if the cord is damaged, the appliance should be
discarded. Never cut the cord.
D. To avoid the possibility of the appliance plug or
receptacle getting wet, position the appliance
to one side of a wall mounted receptacle to
prevent water from dripping onto the receptacle
or plug. A "drip loop" (see illustration) should
be arranged by the user for the cord connecting
appliance to a receptacle. "The drip loop" is that
part of the cord below the level of the receptacle or
the connector if an extension cord is used, to prevent water traveling along
the cord and coming in contact with the receptacle. If the plug or receptacle
does get wet, DO NOT unplug the cord. Disconnect the fuse or circuit breaker
that supplies power to the appliance. Then unplug and examine for presence of
water in receptacle.
3. This appliance is not intended for use by persons (including children) with
significantly impaired physical or mental capabilities, unless they have been
given supervision or instruction concerning the use of the appliance by a person
responsible for their safety. Children should always be supervised to ensure that
they do not play with the appliance.
4. To avoid injury, do not touch moving parts or hot parts.
5. CAUTION - Always unplug or disconnect all appliances in the aquarium from
electricity supply before placing hands in water, before putting on or taking off parts
and while the equipment is being installed, maintained or handled. Never yank cord
to pull plug from outlet. Grasp the plug and pull to disconnect. Always unplug an
appliance from an outlet when not in use.
6. Do not install or store the appliance where it will be exposed to weather or
temperatures below freezing. FOR INDOOR HOUSEHOLD USE ONLY.
7. Make sure the appliance is mounted correctly and securely positioned on the
aquarium before operating the appliance.
8. If an extension cord is necessary, a cord with proper rating should be used. A
cord rated for less amperes or watts than the appliance rating may overheat. Care
should be taken to arrange the cord so that it will not be tripped over or pulled. The
connection should be carried out by a qualified electrical installer.
9. The socket-outlet shall be installed near the equipment and shall be easily
accessible.
10. LED power supply shall not be positioned on or into the cover frame.
11. "Z" attachments: The external flexible cable or cord of this luminaire cannot be
replaced; if cord is damaged the luminaire shall be destroyed.
SAVE THESE INSTRUCTIONS
For the complete use and understanding of this product it is recommended that this
manual is thoroughly read and understood. Failure to do so may result in damage to
this product.
The Fluval Prism is a remote-controlled, high-output spotlight LED that allows the user to
create up to 80 multi-color lighting options, including special effects, to match any décor or
desired mood effect.
INSTALLATION AND USAGE:
Please verify that all components of the light fixture are undamaged before putting it
into operation. Before any kind of maintenance, always
disconnect electrical supply of the light fixture.
IMPORTANT: The Fluval Prism is designed to work only
when fully submerged in water. Do not operate dry.
• Affix light fixture to the inside glass of the aquarium (Top
right or top left corner of aquarium, just under the water
REMOTE CONTROL:
To operate:
To change the battery:
Remote Control Keypad Functions
a) Power: Press these buttons to turn LED on or off
b) Brightness (+ / - ): Press these buttons to increase or
c) R/G/B/W LED color: Press any of these buttons to add
d) Special Effects: Press any of these buttons to add
e) All color spectral cycle: Setting slowly cycles through
MAINTENANCE:
For maximum LED performance, it is recommended that the fixture and the LED lens be
cleaned on a weekly basis. Unplug transformer prior to cleaning the light fixture and remove
from aquarium. Wipe exposed surfaces carefully with a damp cloth to remove any mineral
deposits that may collect over time. Do not use detergents or harsh cleaners as it can damage
the light fixture. Make sure wires are dry before re-connecting to the power source.
BASIC TROUBLE-SHOOTING:
If the fixture does not work, ensure that all plugs and wires are firmly connected.
WARRANTY
2 YEAR LIMITED WARRANTY
The Fluval Prism LED is guaranteed against defects in material or workmanship under normal
aquarium usage and service for 2 years. We reserve the right to repair or replace at our
option. This warranty does not apply to any light fixture that has been subjected to misuse,
negligence or tampering or commercial use. No liability is assumed with respect to loss or
damage to livestock or personal property irrespective of the cause thereof. This does not
affect your statutory rights.
FOR AUTHORIZED WARRANTY REPAIR SERVICE:
For Authorized Warranty Service please return (well packaged and by registered post) to
the address below enclosing dated receipt and reason for return. If you have any queries or
comments about the operation of this product, please let us try to help you before you return
the product to your retailer. Most queries can be handled promptly with a phone call. When
you call (or write), please have all relevant information such as model number, age of product,
details of aquarium set-up, as well as the nature of the problem.
CANADA: Consumer Repair, Rolf C. Hagen Inc., 20500 Trans Canada Hwy,
Baie d'Urfé, QC H9X 0A2
U.S.A.: Rolf C. Hagen (U.S.A.) Corp., 305 Forbes Blvd, Mansfield, MA. 02048
UK: Rolf C. Hagen (UK) Ltd, Customer Service Department California Drive, Whitwood Ind Est.,
Castleford West Yorkshire WF10 5QH http://faq.hagencrm.com/?uk
CALL US ON OUR TOLL-FREE NUMBER:
CANADA ONLY: 1-800-554-2436 between 9:00 a.m. and 4:30 p.m. Eastern Standard Time.
Ask for Customer Service.
U.S. ONLY: 1-800-724-2436 between 9:00 a.m. and 4:00 p.m. Eastern Standard Time.
Ask for Customer Service.
U.K. ONLY: Helpline Number 01977 521015. Between 9:00 AM and 5:00 PM, Monday to
Thursday and 9:00 AM and 4:00 PM on Friday (excluding Bank Holidays).
Illustration 1
line). (See illustration 1)
Note: Light fixture should be positioned so that it will illuminate the tank and its
inhabitants.
• Ensure there is a direct line-of-sight between the fixtures sensor (located at top of
light) and the remote control. Press suction cup firmly against the glass to ensure proper
adhesion. Note: Make sure the light fixture is mounted correctly and securely positioned on
the aquarium before operating the appliance.
• Connect the plug to the electrical supply.
• Remove plastic cover from wireless remote; remove
the clear plastic tab located at the bottom of the
remote to activate the battery connection (the remote
should already have the battery included).
• Ensure there is a direct line-of-sight between the
fixtures sensor (located at top of light) and
the remote control. (See illustration 2)
• Point the remote so that the infrared sensor on the
remote activates the sensor on the light fixture.
Battery compartment is located on back of remote, to open:
• Slide "Release" tab to the right while
gently pulling out the battery door.
• Insert (1) 3V battery
• Gently push battery door closed.
decrease light intensity
or remove red, green blue or white and to adjust the
color intensity
special lighting effects
every color spectrum
RECYCLING: This symbol bears the selective sorting symbol for waste electrical and
electronic equipment (WEEE). This means that this product must be handled pursuant
to European Directive 2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment. Check with your local Environmental Agency for possible
disposal instructions or take to an official council registered refuse collection point.
Electronic products not included in the selective sorting process are potentially
dangerous for the environment and human health due to the presence of hazardous
substances.
Illustration 2
a
b
d
c
e