Air Filter - Husqvarna FS 305 Manuel D'utilisation

Maintenance (with the
9
engine stopped)
"Engine Maintenance" : refer to
the engine maintenance booklet.
• After use, clean the machine.
• Lubrication : apply a moderate amount of
bearing lubricant to the nipples in the
depth adjustment (depending on
the frequency of use). Weekly lubrication
is recommended.
OIL
• Check the engine oil everyday. Refer to
the engine manual for oil change
schedule. Use :
SAE 10W30 engine oil with API class
•
MS, SD, SE or better for PETROL
engines.
Dispose of the old oil as laid
down by the regulations in force.
• To change the oil, remove the blade, lower
the saw to horiz o t n l a p o sition and then
place the tray by the drain outlet (L) [
4].
FIG.
Store in a safe place, out of
reach of children
Maintain tools carefully

AIR FILTER

• Read engine owners manual for
maintenance intervals. For extremely
dusty conditions you may have to clean
the air filter element 2 to 3 times a day.
• Replace any damaged filters or gaskets.
CAUTION!
The filter must not be cleaned
with compressed air, this will
damage the filter. Filters can be
vacuumed out for cleaning but
avoid hitting or dragging items
across the surface as this will
damage the filter.
Paper filters are to be disposed
of correctly and replaced.
A polyester filter can be cleaned
via vacuuming or low pressure
washing.
Do not use high pressure
washing, this will damage the
filter.
A damaged filter must always be
replaced.
A washed filter must be 100% dry
before being placed back onto the
equipment.
Store in a safe place out ot reach
of children.
Remove all adjustment tools and
wrenches
Store diamond tool in a safe
place so it cannot be bent or
damaged.
10 Engine belt tension
It may be necessary after using a few times
to retension the belts, without over-
tightening them. To do this :
loosen the 2 nuts (S) fixing the engine to
•
the chassis, without removing them
[ 5];
SEE FIG.
tighten the tensioning nuts (N), these
•
screws pull the engine up.
at normal tension, tighten the engine
•
fixing nuts (S).
SEE
11 Important advice
• Periodically, tighten the nuts and bolts
and particularly after the first few hours of
use.
• Check belt tensions, tighten them without
overdoing it.
• When not used , it is recommended the
disc be removed and suitably stored.
• Make sure the disc is correctly tightened.
• Make sure the disc supports surfaces, the
adaptor plates and the spindle are kept
clean.
The manufacturer declines all
responsibility for loss or damage
resulting from misuse or any
modification,
powering that does not conform
to the manufacturer's original
specifications.
At the work station, the sound
pressure level may exceed
85xdbx(A)
In this case individual protection
measures must be taken.
When working in a limited or
closed area, make sure that the
ventilation is adequate. The
exhaust gases contain carbon
monoxide (exposure to this toxic
gas can
consciousness and can be fatal).
12
Contact a Husqvarna construction Products
service center for equipment repaire. For
engine repaires, contact engine supplier
service.
13
For quick supply of spare parts and to
avoid any lost time it is essential to quote
the data on the manufacturer's plate fixed
to the machine and the part number of the
part to be replaced with every order.
Item number
14
• Main materials :
Engine: Aluminium (AL), Steel (AC),
•
Motor :
Machine : Steel sheet (AC),
•
Machine :
Machine :
alteration or
The instructions for use and spare parts
found in this document are for information
only and are not binding.
As part of our product quality improvement
policy, we reserve the right to make any
cause loss of
and all technical modifications without prior
notice.
Repairs
Spare parts
00000000 (0)
Quantity
See exploded view
Only use original Husqvarna parts.
See IPL for parts.
Scrapping
In the event of deterioration and
scrapping of the machine, the
following items must
disposed of in accordance with
the requirements of
legislation in force.
Copper (CU), Polyamide (PA)
Cast iron (FT)
Aluminium (AL)
be
the
12