Scheppach 4901307901 Traduction Du Manuel D'origine page 21

pushed against the saw blade. Be aware: After sawing
the work piece, the saw blade guard has to return to
its resting position.
3 Connect the extraction hose (12) with one end on the
extraction port on the saw blade guard and with the
other end on the extraction nozzle.
4 For removal of the saw blade guard (5), disassemb-
le the extraction hose first, then loosen the butterfly
screw and pull off the saw blade guard (5).
Note: The saw blade guard (5) has to be in the operating
position at all times to prevent contact with the saw bla-
de. It should lift onto the work piece during sawing.
STEP 7.
ASSEMBLY OF THE LONGITUDINAL STOP, FIG. 7
1 Longitudinal stop
1 Make sure the levers at the front end of the fence are
loosened and position it with the back end onto the
back stop rail.
2 Position the fence on the front stop rail.
3 Fold the lever down to fix the longitudinal stop.
Commissioning
Follow the safety notices!
Important: Commissioning of the power tool may only take
place with completely assembled protective and safety
equipment.
The protective hood has to be lowered onto the work pie-
ce for every process step.
Before turning on the power tool, all protective and safety
equipment must be fitted according to instructions.
The saw blade has to be able to move freely.
Check the wood which has previously been worked on for
foreign objects (nails, screws etc.). Remove all foreign ob-
jects.
Connect the power tool to an earthed power socket.
Before turning on the main switch, make sure that the
saw blade is mounted correctly and all moving parts run
smoothly.
Warning: If you have any doubt, get a professional to set
up the power tool. It is too dangerous to work on assump-
tions.
TURNING THE DEVICE ON AND OFF
• The saw can be turned on by pressing the green but-
ton "I".
• To turn off the saw, press the red button "0".
CHANGING THE CUTTING HEIGHT, FIG. 9
The power tool has to be set up in such a way that the
top of the highest sawtooth is a little higher than the work
piece.
• Set the required cutting height by turning the height
adjuster wheel (2).
• Turning anti-clockwise increases the cutting height.
• Turning clockwise decreases the cutting height.
SETTING THE SAW BLADE ANGLE, FIG. 10
• Loosen the clamp (K) and push the handwheel (2) to-
wards the saw until it engages with the tooth system.
• Adjust the handwheel until the indicator points to the
correct angle on the dial (S).
• Tighten the clamp again after set-up.
The dial (S) can be adjusted when checking the exact
angle of the saw blade.
When the power tool is off and the mains plug disconnec-
ted, put an adjustable try square against the saw blade.
Adjust the handwheel until the saw blade is parallel to
the adjustable try square. Then set the indicator of the
dial to 0°.
WORKING WITH THE TABLE EXTENSION, FIG. 11
To increase the useable width of the table, use the ta-
ble extension.
• Pull the lever (L) up to loosen the lock on the table
extension.
• Push the table extension into the required position.
• When you have set the required position, lock the table
extension by pushing the lever back down.
Operating instructions
Warning!
• After every adjustment, we recommend a test cut to
check the measurements you set.
• After turning on the saw, wait until the saw blade has
reached its maximum revolution speed before carrying
out the cut.
• Always use the device with working extraction.
• Regularly check and clean the extraction ducts.
PROTECTION AGAINST OVERLOAD
This power tool is equipped with protection against over-
load. If the protection against overload is triggered, do
the following:
1 Disconnect the power tool from the power supply.
2 Leave the power tool to cool down.
3 Check the power tool for potential damage that may
have occurred. Have the damage repaired before using
the power tool again.
4 Connect the power tool to the power supply.
5 Turn on the power tool as described and start using it.
WORKING WITH CIRCULAR SAWING MACHINES
Cutting wide work pieces, fig. 12
Width of work piece to be processed more than 120 mm
Tool: Circular saw blade for longitudinal cut
Process: Set the longitudinal stop according to the width
of the work piece. Ensure a safe hand position. If narrow
work pieces are cut off in the process, the infeed is car-
ried out with the right hand only or using a push stick in
the tool area. If there is a risk of the work piece getting
trapped between the circular saw blade, riving knife and
fence, an auxiliary fence has to be used.
Note: On the pictures, the upper extraction hood was only
suggested or left out in some cases to show the process
or the equipment more clearly. The upper extraction hood
is required for all shown processes.
21