MSW -DRAIN CLEAN 23E Manuel D'utilisation page 8

DEVICE OPERATION DESCRIPTION – APPLICABLE TO MODEL MSW-DRAIN CLEAN 23E (6350):
Operation:
1. After receiving the device, assemble it as shown in the attached drawing. Before commencing
operation, ensure that neither the device nor the power cable are damaged. Next, make sure that the
switch at the motor is in the "OFF" position. If it is not, put it in the middle position.
2. When all the elements are in place, take the coil out of the drum and thread it through the outlet
nozzle. In order to do so, undo the black knob, thread appropriate length of the coil through the
nozzle opening and tighten the knob, so that the coil could perform its function when the engine is on.
Overtightening the knob will jam the coil in the device, and if the knob is too loose, the coil will not
be able to come out or retract. When the coil is ready, fit an appropriate tip with the power supply
turned off. In order to attach the tip to the coil, undo the bolt located at the end of the coil, fit the tip
and tighten the bolt, so that the tip was firmly attached to the coil.
3. Next, connect the device to the mains outlet. Every time before turning the device on, it must be
tested as follows: press the "RESET" button, turn the device on as per the following guidelines, and,
during operation, press the "TEST" button. If the device stops, it means that the GFCI switch works
properly and the device can be used safely. If the device fails to stop after pressing the TEST button,
immediately disconnect it from the power supply.
After the test, press the "RESET" button to operate the device normally. If during operation the
„RESET" button goes off automatically, or if it is impossible to turn it on, it means that the device
is most likely defective. In such a case, disconnect the device from mains immediately and follow the
instructions provided in the section "REGULAR INSPECTION OF THE DEVICE".
4. In order to start clearing, place the device about 20 cm from the place of inserting the coil, insert the
coil into the opening in such a way that after insertion the coil does not twist and curl. Then, switch
the rotation direction switch located at the engine and put the lever in the appropriate position.
Possible settings:
Switch in the FOR position + lever in the upper position – the coil rotates clockwise and comes out.
Switch in the FOR position + lever in the lower position – the coil rotates clockwise and retracts.
Switch in the REV position + lever in the upper position – the coil rotates counter clockwise and
retracts.
Switch in the REV position + lever in the lower position – the coil rotates counter clockwise and
comes out.
Next, you can turn the device on using the pneumatic pedal provided with the device.
Always be ready to immediately stop the power device! Caution! The coil is about 23m long – it is not
recommended to remove impurities located near this distance.
5. In order to wind the coil in, set the lever and the switch in the appropriate position (as specified in
item 3 above) and press the pedal.
6. After completing the clearing, put the switch in the "OFF" position and disconnect the device from the
mains. Remember to thoroughly clean the device before winding the coil.
14
10
9
MSW-POWER DRAIN CLEAN 2.3E (6359)
8
MSW-POWER DRAIN CLEAN 4.6E (6360)
1
11
DESCRIPTION OF THE DEVICE OPERATION – APPLICABLE TO MODELS MSW-DRAIN CLEAN 2.3E
(6351) | MSW-POWER DRAIN CLEAN 2.3E (6359) | MSW-POWER DRAIN CLEAN 4.6E (6360)
Operation:
1. Before commencing operation, ensure that neither the device nor the power cable are damaged. Next,
make sure that the switch at the motor is in the "OFF" position. If it is not, put it in the middle
position. And put the lever in the upper position.
Rev. 16.08.2017 Rev. 16.08.2017
1
2
3
4
5
8
7
6
1
10
9
2
3
6
4
5
7
2
5
3
4
9
6
7
8
10
Description of the device:
1. Handle
2. Motor switch
3. Lever
4. Enclosure
5. Coil
6. Protective gloves
7. Wrench
8. Tip set
9. Adjustable legs
10. Lubrication hole
Description of the device:
1. Lever/handle
2. Locking lever/rear of the device
3. Coil
4. Protective gloves
5. Tip set
6. Legs
7. Wrenches
8. Tube
9. Container
10. Lubrication holes
Description of the device:
1. Outlet nozzle
2. Lever
3. Protective pipe joint
4. Protective pipe
5. Coil
6. Protective gloves
7. Wrenches
8. Tip set
9. Motor
10. Wheels
11. Frame
15