Proper Use - Top Craft TCR 450 Mode D'emploi

Anleitung TCR 450 4-spr.
GB
Check the screws regularly to see that they are
properly tightened.
The mains voltage must be the same as the
voltage specified on the rating plate.
Check the power cable regularly for signs of
damage or aging. Never use the grass trimmer if
the power cable is in less than perfect condition.
Power cables used with the trimmer must not be
of a lighter duty class than HO7RN-F rubber-
insulated flexible cables according to DIN 57282
/ VDE 0282 with a minimum diameter of 1.5 mm
Plug connectors must be equipped with earthing
contacts and the coupling must be rain-water-
protected.
Keep cables and other objects out of the area
you want to cut.
If you have to lift the grass trimmer to move it,
switch off the motor and wait for the rotating tool
to stop. Before you leave the trimmer, switch off
the motor and pull out the power plug.
Before you connect the grass trimmer to the
power supply, make sure that none of its moving
parts are damaged and that the line spool is
correctly inserted and fastened.
Never cut against hard objects when using the
grass trimmer. This is imperative to avoid
causing injury to the user and damage to the
trimmer.
Use only original replacement parts for repair
and maintenance purposes.
Have repairs carried out only by a qualified
electrician.
Examine the grass trimmer for signs of wear or
damage each time before you use it and after
any collisions. Have essential repairs carried out
without delay.
Always keep your hands and feet away from the
cutting mechanism, particularly when you switch
on the trimmer.
After pulling out new line, always return the
trimmer to normal working position before you
switch it on again.
Never use replacement parts or accessories
which are not foreseen or recommended by the
manufacturer.
Pull out the power plug before carrying out any
inspection, cleaning or other work on the trimmer
and whenever it is not being used.
m
Caution! The nylon line will run on for a few
seconds after the tool is switched off!
12
24.10.2001 12:23 Uhr
3. Explanation of rating plate
Item 1: Important! Read the operating instructions
Item 2: Wear goggles and a face mask.
Item 3: Never use the grass trimmer in the rain, in
Item 4: Keep a safe distance of at least 5m from
2 .
Item 5: Using the grass trimmer as an edge cutter.
4. Technical data: TCR 450
Art. No.:
The noise level of this machine may exceed 85
dB(A). In this case, noise protection measures need
to be introduced for the user. The machine's noise
was measured in accordance with IEC 59 CO 11,
IEC 704, DIN 45635 Part 21, NFS 31-031
(84/538/EEC).
The level of vibrations emitted from the handle is
1.2 m/s
with ISO 5349.
5. Assembling the guard hood and the

6. Proper use

Tool runs
on!
The trimmer is designed for cutting lawns and small
areas of grass in private and hobby gardens.
Tools for private and hobby gardens are not suitable
for use in public facilities, parks and sport centers,
along roadways, on farms or in the forestry sector.
Seite 12
(see picture 2) on the grass trimmer
carefully before you use the hedge trimmer.
damp conditions or on wet lawns.
other persons.
Voltage
Power rating
Cutting width
Speed
Nylon cutting line
Sound pressure level LPA
Sound power level
Vibration aw
Weight
2 . Measurements were taken in accordance
handle
Plug the guard hood on the motor head and
fasten with the supplied screws (see Figure 3).
First fasten the screws shown in Figure 4, then
you can fasten the two screws in conjunction
with the edge guide (see Figure 5).
Fit the handle as shown in Figure 6.
230V ~ 50 Hz
450 W
ø 30 cm
10,000 rpm
ø 1.2 mm
81 dB(A)
92 dB(A)
1.2 m/s 2
3 kg
34.014.83