Manufacturer's Warranty; Spare Parts Lists - Roller Smart-Cut Notice D'utilisation

eng
5.4. Fault: Electric pipe cutter, cordless electric pipe cutter does not start.
Cause:
● Mains lead defective (ROLLER'S Smart-Cut).
● Power tool defective.
● Worn carbon brushes.
● Battery fl at or defective (ROLLER'S Smart-Cut 11 V).
● Feeding pressure too high.
5.5. Fault: Cutting wheel becomes blunt or breaks out after 1 or 2 cuts.
Cause:
● Cutting in a cutting notch in which the previous cutting wheel already
became blunt or was damaged.
● Unsuitable cutting wheel.
● Pipe material is unsuitable for cutting.
5.6. Fault: Cutting of the pipes leaves marks on the outside of the pipes.
Cause:
● Rollers of the pipe rest (6) soiled.
● Rollers of the pipe rest (6) damaged.
6. Disposal
ROLLER'S Smart-Cut, ROLLER'S Smart-Cut 11 V, rapid charger and batteries
may not be thrown in the household waste when they are fi nished with. They
must be disposed of properly by law. Lithium batteries and battery packs of all
battery systems may only be disposed of in the discharged state, all contacts
of incompletely discharged lithium batteries and battery packs must be covered
with insulating tape.

7. 7. 7 Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which ROLLER is not responsible, shall be excluded from the
warranty
Smart-Cut 11 V Smart-Cut 11 V).
Smart-Cut 11 V Smart-Cut 11 V, rapid charger and batteries
Remedy:
● Have the mains lead changed by qualifi ed personnel or an authorised ROLLER
customer service workshop.
● Have the power tool checked/repaired by an authorised ROLLER customer
service workshop.
● Have the motor changed by an authorised ROLLER customer service
workshop.
● Charge the battery with the rapid charger or change the battery. e r e rapid charger or change the battery.
● Reduce feeding pressure.
Remedy:
● Place the cutting wheel next to the notch with the remaining fragments.
● Select and change cutting wheel according to the pipe to be cut.
● Only use approved pipes, see 1.3.
Remedy:
● Clean rollers with machine cleaner, then protect against rust.
● Change rollers.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by ROLLER. Complaints will only be accepted if
the product is returned to a customer service station authorized by ROLLER
without prior interference and in a fully assembled condition. Replaced products
and parts shall become the property of ROLLER.
The user shall be responsible for the cost of shipping and returning the product.
A list of the ROLLER-authorized customer service stations is available on the
Internet under www.albert-roller.de. For countries which are not listed, the
product must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is Albert
Roller GmbH & Co KG, Neue Rommelshauser Straße 4, 71332 Waiblingen,
Deutschland.

8. Spare parts lists

For spare parts lists, see www.albert-roller.de → Downloads → Parts lists.
eng
11