Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
D
WALT Tool Connect™
e
WARNING: To reduce the risk of injury, remove accessories
from the tool chuck before any Tool Connect™ interaction.
NOTICE: Always check the tool configuration prior to use.
If you are unsure of the current configuration, press the
mode selector button
12
Home setting as described on the label and this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
D
WALT Tool Connect™ is an application for your smart device
e
(such as a smart phone or tablet) that connects the device to
your tool to allow you to configure specific tool functions. Refer
to Mode Selector.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D
WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D
WALT Tool Connect™ application at:
e
•
Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from the Tool.
•
Follow the instructions in the app to create your Tool
Connect™ account.
•
On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to the app.
•
To connect your tool with the D
app, at the appropriate screen, press the mode selector
button
for 3–5 seconds, then wait for the tool to
12
connect. The tool can only be connected to one Tool
Connect™ account at a time.
•
Once the tool has been connected, you can confirm that
you would like to register the product.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
D
WALT service center. Do not attempt to replace the coin cell
e
battery yourself.
WARNING: Danger of explosion if battery is
incorrectly replaced.
WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead
to death.
•
Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away from children.
(Fig. D) to set the tool to the
WALT Tool Connect™
e
•
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
•
If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithium salts.
•
Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recycling facility.
OPERATION
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury. Exception—Tool Connect™
functions require battery to be installed.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode button
12
(Fig. D) to set the tool to the factory
default configurations as described on the label and
this manual.
Proper Hand Position (Fig. K)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the top of the drill as
shown, with the other hand on the main handle
Screwdriver Operation (Fig. E)
1. Turn the torque adjustment collar 3 to the desired position.
2. Select the desired speed/torque range using the
gear shifter 4 to match the speed and torque of the
planned operation.
nOTE: Use the lowest torque setting required to seat the
fastener at the desired depth. The lower the number, the
lower the torque output.
3. Insert the desired fastener accessory into the chuck as you
would any drill bit.
4. Make some practice runs in scrap or on unseen areas to
determine the proper position of the clutch collar.
Always start with lower torque settings, then advance to higher
torque settings to avoid damage to the workpiece or fastener.
EnGLIsh
16
.
37
Publicité
Table des Matières
