Assembly - RIDGID HD14000 Mode D'emploi

INTRODUCTION
TOOL NEEDED
Phillips Screwdriver
UNPACKING
This Product Requires Assembly.
Check all parts from carton against the Carton Contents List.
If any parts are damaged or missing, contact 1-800-4-RIDGID
(US and Canada) or by email at info@ridgidvacs.com.
CARTON CONTENTS LIST (Fig. 1)
Key Description
A* Powerhead Assembly .................................................1
B* Dust Drum Assembly .................................................1
C* Drain Cap ....................................................................1
D Carry Handle / Power Cord Wrap Assembly ..............1
E Pan Head Screw, #10 x 3/4" (19 mm) .....................10
F Hose Storage Clip .......................................................2
G Caster Foot w/Storage .................................................4
H Caster ...........................................................................4
I* Qwik Lock™ Filter ........................................................1
J Accessory Caddy .........................................................1
K Tug-A-Long Positive Locking Hose with Dual-Flex ...1
L Extension Wand ...........................................................2
M Utility Nozzle .................................................................1
N Wet Nozzle ...................................................................1
O Car Nozzle ....................................................................1
P Owner's Manual ...........................................................1
* These parts come preassembled.
A*
D
E
F
G
H
P
SP7050-2 ESF.indb 4 SP7050-2 ESF.indb 4
Qty
Fig. 1
I*
J
B*
K
C*
L
M
N
O

ASSEMBLY

CASTER/CASTER FOOT ASSEMBLY (Fig. 2)
NOTE: Remove Powerhead Assembly from Dust Drum
prior to assembly of Casters and Caster Feet.
1. Place Caster Foot (G) upside down on the floor.
2. Place the Caster (H) into the Caster Foot (G): Insert
the Caster Stem into Caster Foot Socket.
3. Push on the Caster until the Caster Ball end snaps fully
into the Caster Foot Socket and the Caster swivels
freely. Repeat for other Three Casters and Caster Feet.
4. Turn Dust Drum (B) upside down on floor.
5. Place Caster Foot with Caster over Drum Post and press
firmly in place. Repeat for the other Three Caster/Caster
Foot Assemblies (G & H).
6. Four Screws are available for optional assembly of the
Caster Feet into the Drum. If desired, locate the Four
#10 x 3/4" (19 mm) Pan Head Screws (E) in loose parts
bag. Insert a Screw through the Caster Foot Hole and
into the Dust Drum (B). Tighten securely. Repeat for the
remaining Caster/Caster Foot Assemblies.
7. Turn the Dust Drum (B) upright.
Caster Stem
(G)
Caster Foot
Socket
(B)
Drum Post
ACCESSORY CADDY ASSEMBLY (Fig. 3)
1. To Attach the Accessory Caddy to the Dust Drum:
Position the Accessory Caddy (J) on the back of the
Dust Drum (B) and align the Locking Tabs.
2. Slide the Accessory Caddy Tabs into the
Dust Drum (B) and push the Locking Tabs in until
you hear a click. Pull on the Accessory Caddy (J)
to confirm it has locked into place.
ASSEMBLED
(J)
Locking
Tab (2)
Bottom Tab (2)
Drum Bottom Slot (2)
4
Fig. 2
(H)
(E)
Caster Foot Hole
Fig. 3
Drum Upper
Slot (2)
(B)
3/2/21 12:12 PM 3/2/21 12:12 PM